Kamrytech X10 Protank Rebuildable Atomizer with DCT Pyrex Tank (4.0ml)

[Pur3Rush]

Protank or evod head will NOT fit on the x10's ordered from fast tech. The air hole inside the tank itself is slightly smaller diameter. Also, the atomizer hole diameter is a bit smaller as well. The x10's work well, but are not compatible with anything else. Same thing with a protank type clone ordered from fast tech. Hopefully this makes sense.

Basically the tank airhole diameter is smaller than the diameter of real protank, evod heads. The atty heads will screw into the bottom plate but because of the size discrepancy, they won't go in. Booooo.

 

[nelsonm64]

weird, i'm using an X10 that arrived today and put a pro tank head in it right off the hop and its working?

 

[Fullknight]

weird, i'm using an X10 that arrived today and put a pro tank head in it right off the hop and its working?

Great I have one on the way. I have an X9 Protank clone with an EVOD head in it!


Sent from my iPhone using Tapatalk

 

[mgmrick]

Been using these x10's for a couple of weeks now. Out of the box I was not impressed. I drilled out the two air holes and inserted a protank coil rebuilt with cotton wick. I would not trade these for anything now

 

[Jimi D.]

Been using these x10's for a couple of weeks now. Out of the box I was not impressed. I drilled out the two air holes and inserted a protank coil rebuilt with cotton wick. I would not trade these for anything now

You'd be great with a mech with quads

 

[droach3]

Got mine from fasttech today. I really like the design. It is ABS. I put a tank clouder(has not cracked anything yet) in it and so far so good.
One complaint. IF i screw it down to my provari it sits too flush and allows no airflow so I have to back it off a bit. A little irritating.

 

[droach3]

Got mine from fasttech today. I really like the design. It is ABS. I put a tank clouder(has not cracked anything yet) in it and so far so good.
One complaint. IF i screw it down to my provari it sits too flush and allows no airflow so I have to back it off a bit. A little irritating.

Follow up after a day using at work, traveling in pocket etc.

I hate this good for nothing piece of ABS and metal piece of monkey dung!!!

Sorry I had very high hopes. Pulled it out of my pocket in the bathroom for a little stall vapeing and loosened a hair for air flow and get a huge mouth full of juice.

Back in pocket get to truck after work and do the oh so familiar Protank juice whip and then take a long steady pull of....JUICE in my mouth. ...! take it off Provari only to find juice all over the connection and the juice well. I try turning up temp to burn off excess and that doesnt work. I am done with China!!! (I lie I just wont buy another one of these)

 

[mgmrick]

As I posted before out of the box it is not very good. I use a protank coil and rebuild it with cotton wick

Follow up after a day using at work, traveling in pocket etc.

I hate this good for nothing piece of ABS and metal piece of monkey dung!!!

Sorry I had very high hopes. Pulled it out of my pocket in the bathroom for a little stall vapeing and loosened a hair for air flow and get a huge mouth full of juice.

Back in pocket get to truck after work and do the oh so familiar Protank juice whip and then take a long steady pull of....JUICE in my mouth. ...! take it off Provari only to find juice all over the connection and the juice well. I try turning up temp to burn off excess and that doesnt work. I am done with China!!! (I lie I just wont buy another one of these)

 

[e-pipeman]

I changed the supplied head with an Evod head (it was working with the supplied head but had a slightly "off" flavour) and it has been working like a champ for me. The head can loosen a little when unscrewing, and then the dreaded gurgle/liquid in mouth can occur. If the head is tightened up (in mine at least) it works perfectly right to the bottom of the tank.

 

[Jimi D.]

Pure JUNK!!!!

 

[droach3]

I will try another head but for now it has left a bad taste in my mouth...literately bad e-juice taste.

 

[HughDaHand]

I have been using these for a few weeks now and I really like them with my cotton rebuilt evod heads. The draw is a little tight so I think I am going to try drilling out the air holes like mgmrick did. I do get a couple of drops of juice in my connection every now and again but that seems to happen with all my BCC clearos. I also agree that the included heads have a funny taste to them out of the box, but I get a funny taste from all silica so that may just be me.

 

[mgmrick]

I did not like these out of the box. I rebuild all my coils using cotton. The coil included with these has a much smaller air hole in the air tube. Using a protank coil with cotton and drilled out the 2 air holes about 1 size bigger.

There is another atty out now with 3 air holes in the bottom and a bigger air tube (same as the protank) bigger they hold 5ml of juice and are pyrex glass with metal jacket. Those ones work out of the box but these x10's work fine if you change the coil and drill out the air holes

 

[JaneinMesa]

I loved mine along with the X10 heads from fasttech. The first heads I ordered did not have a knurled stem, but now they do. The problem is the BASE SNAPS OFF the tank VERY EASILY and YOU CANNOT BUY REPLACEMENT BASES anywhere! The entire tank is then useless. I now have a bunch of heads I need to find a tank for. I don't want glass. I'm bummed because, for me, this tank was working really well and the heads were reasonably priced. I may order one more and try putting a bit of epoxy around the base stem to see if that helps it's durability.