Kayfun Long (extended) chimney & tank??? anywhere? (clone ok)
- Thread starter Phone Guy
- Start date
- th_trl_thread_readers 0
- Status
Thanks for the link. I'm not to keen on buying from ebay sellers anymore.... been messed over a few times. Even though this is a relatively simple and small purchase. Plus all I really "need" is the chimney... I recently got a flat cap from FT, and it allows me to use any drip tip on my clone 3.1, but I'd like it to hold more juice, so I was going to buy the extended chimney and add 1 more stainless ring to the top, and continue to use this flat cap. I have found the chimney is stock a couple places for $10 overseas, but then the shipping kills the deal, I'd be better off buying the whole setup from the dude on ebay and get the large m-tank to boot. 
I completely agree.... especially since I'm only chasing the chimney.... the regular m-tank I bought was from madvapes for like $4 or something.... but I got this cap from fasttech
and its solid on top.... if it were hallow (sp?) up in the cap, it would hold another ml of juice easy..... but because its also the top most stainless ring, top filling is not practical. So the goal is to make the Kayfun hold more than the 3ml it holds with this top place installed, by using another ring on top of clear and under this cap. I'm not even 100% sure it will be the right size and work.
I was hopeful there was a clone vendor (ala madvapes, 101vapes, fasttech, etc) that might carry that chimney/m-tank setup all for about $10
Yeah...I agree..I looked around for the long mode setup myself...and was really hesitant to buy them for more than what I paid for my Hcigar KF 3.1 clones. You can also find them on the Russian Svoemesto website for the equivalent of $35 or something.
Vaperev.com has the authentic chimney for $10.00 & tank for $23.50.
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
Quick question though Phone Guy.. I know it's off topic but I am told that you have tons of info on Semovar ...I just got myself a Semovar that is finished like the Russian 91%..do you happen to know what finish is that on the website?
Thanks for the link. I'm not to keen on buying from ebay sellers anymore.... been messed over a few times. Even though this is a relatively simple and small purchase. Plus all I really "need" is the chimney... I recently got a flat cap from FT, and it allows me to use any drip tip on my clone 3.1, but I'd like it to hold more juice, so I was going to buy the extended chimney and add 1 more stainless ring to the top, and continue to use this flat cap. I have found the chimney is stock a couple places for $10 overseas, but then the shipping kills the deal, I'd be better off buying the whole setup from the dude on ebay and get the large m-tank to boot.
Phone Guy, while I don't know this eBayer personally but I have bought from him 3 times, including the long M tank I bought. I can say that in all my cases he was on the up and up. I decided to get the chimney setup from Cloud9 because I was also buying the red LED window for my Semovar. It was far cheaper and I was paying for shipping anyway.
They are out of stock. InTaste has them, but the shipping kills it (from germany). Both pieces end up being about $48 usd shipped (g/t)
Miata beat me to it
it is BetaSomewhere there is a better picture with the finishes and names... here is the one I have on my machine
I'll see if I can find the other picture too and post it here and/or in the semovari provari comparison thread
Last edited:
I found a Canadian website that sells the chimney ...don't know how much the shipping would cost though:
DashVapes - SVOEMESTO KAYFUN V3.1 OR LITE LONG CHIMNEY
DashVapes - SVOEMESTO KAYFUN V3.1 OR LITE LONG CHIMNEY
I completely agree.... especially since I'm only chasing the chimney.... the regular m-tank I bought was from madvapes for like $4 or something.... but I got this cap from fasttech
and its solid on top.... if it were hallow (sp?) up in the cap, it would hold another ml of juice easy..... but because its also the top most stainless ring, top filling is not practical. So the goal is to make the Kayfun hold more than the 3ml it holds with this top place installed, by using another ring on top of clear and under this cap. I'm not even 100% sure it will be the right size and work.
I was hopeful there was a clone vendor (ala madvapes, 101vapes, fasttech, etc) that might carry that chimney/m-tank setup all for about $10
I have the same topcap and also want to put in more juice. I actually found a solution. Using the stock chimney I assembled the tank as follows:
topcap
middle ring
stock bottom ring
It now holds much more juice, without buying anything additional.
Hope this helps.
Last edited:
Vaperev Shop - Accessories - SvoëMesto - Rebuildables
this is where i got mine, they get stock pretty often though sometimes it may take a bit. you can sign up for the email that lets you know when new stock has arrived.
this is where i got mine, they get stock pretty often though sometimes it may take a bit. you can sign up for the email that lets you know when new stock has arrived.
I did the live chat and asked if you could use extra sections to make a tank that fits. The guy said that you have to use the long m-tank....Holy crap! $27.50 for a plastic tank. I would like one but, I don't want to pay that much.
- Status
Similar threads
