Let's Talk Hardware
- Thread starter Pappy
- Start date
- th_trl_thread_readers 0
- Status
Can't say they aren't big enough now. Just put a 1.4 ohm coil in and it's hitting good. Besides the worst that could happen is I screw it up. Wouldn't be the first time.
Yup , they're definitely big enough now , I wonder how in the hell they managed to to screw it up to begin with , wrong settings on the CNC ?
Chinese.
Likely a worn tool. They don't do any SPC over there.
Yup comparing the two you could tell that a different size bit was used.
The guy running the mill probably has to pay for his own tooling so why would he change it. I just hope they build their battleships the same way.
I don't think this would apply to a wicking problem, but is that air flow center pin the same height above the block on both of them? I ask because it's quite a bit higher than on the authentic KFLs.
It's higher because I had to sand the block a little to get the air hole in the post to line up with the body air hole. It was 1/8 turn off.
Depends on what you want to spend. What you're going to be using it for. There's different options, corded , cordless. Mine was $100 at Lowe's. But I had a $50 gift card and a $10 coupon so I paid $40. And it's the Dremel brand.
MP , I'm looking at this one myself .
Dremel 3000-1/24 1 Attachment/24 Accessories Rotary Tool - Power Rotary Tools - Amazon.com
And this looks handy too .
Dremel 220-01 Rotary Tool Work Station - Power Rotary Tool Accessories - Amazon.com
I replaced my old coil in my RSST to a 28ga 1.2 ohm nano... 36 nic is now way too much in it...
so,... I believe its safe to say there is a relationship between ohms and nic level...
the lower ohms creates more heat which vaporizes the nic to higher density which causes you to cough
possibly an inverse relationship lower ohms higher cough factor... now just to figure out the math
so,... I believe its safe to say there is a relationship between ohms and nic level...
the lower ohms creates more heat which vaporizes the nic to higher density which causes you to cough
possibly an inverse relationship lower ohms higher cough factor... now just to figure out the math
Last edited:
What?
On second thought don't try to explain it'll just confuse me more.
i got confooosed figuring it out ( but the numbers work)
thats the beauty of theoretical math, if the numbers work, than its right, even if no one understands what you were implying...
such as ... 0/0 = 1
I proved that it is so...
any number over itself = 1
and since 1X 10 to the - infinity is 0
and that number over its self, therefore = 1
I proved that it is so...
any number over itself = 1
and since 1X 10 to the - infinity is 0
and that number over its self, therefore = 1
I will say I enjoy my Hana DNA30 (20 vs 30 wouldn't matter as I'll never get to those limits) but the vape is nice. I just got lucky and was able to score one after Vapebash.
Well, my black Vapor Shark DNA30 with black shark skin arrived today. I slapped a dual coil 0.38Ω Cyclone on it and so far, so good. The box shape and the rubber shark skin should make it better for my boat rides. And it is so small that only a portion of the atty shows outside of my hand. It seems very well built, but I've only had it for a few hours and I squeezed it into the skin almost as soon as I got it. That is one tight skin!
Not sure I like the proprietary 1200mAh battery - I've gotten pretty used to higher capacity batteries. But if the mod lasts, I think the small form factor will make up for it.
I'll try it with a KFL while out & about tomorrow.
Not sure I like the proprietary 1200mAh battery - I've gotten pretty used to higher capacity batteries. But if the mod lasts, I think the small form factor will make up for it.
I'll try it with a KFL while out & about tomorrow.
Newest additions.
Atomic RDA (legit)
Cyclone with AFC and a LP/SL REO.
Frak me it's beautiful.
Sent from my SAMSUNG-SGH-I747 using Tapatalk
- Status
Similar threads
- Locked
- Locked
