Low Ohm Atty

[okcodemonkey]

I currently use 1.5 ohm joyetech atties in my UFS. I enjoy them for the most part but miss the heat I get with my Provari running at 4.4-4.5 with them. I would prefer to buy atties instead of using RBAs. Anyone know anyone that sells atties at 1.1-1.2 ohms? Or any atties that might produce more heat at whatever ohm?

 

[Unforeseen]

Unfortunately, the lowest is 1.5 ohms for the moment. Perhaps in the future they'll make a 1.2 ohm atomizer. Seeing you have a GGTS. Buying a Kick will help you get a warmer vape from your atomizers.

 

[Scottinboca]

I know it's not the safest thing and I don't recommend this to anyone, but there's always staking batteries.

 

[okcodemonkey]

Unfortunately, the lowest is 1.5 ohms for the moment. Perhaps in the future they'll make a 1.2 ohm atomizer. Seeing you have a GGTS. Buying a Kick will help you get a warmer vape from your atomizers.

Yeah may be time to get a kick again. I did not like the killing of the battery life I had with it in the past. Provari lasts much longer at the same wattage. Wish people would invest in improving manufactured attys, and not just rebuildables. Almost seems like the off the shelf atty is going away. Are the Cisco, Ilenvapes or Hh357s any hotter than a joyetech at same voltage/resistance?

I know it's not the safest thing and I don't recommend this to anyone, but there's always staking batteries.

I have no problem with that. May look at getting a few 5V batteries to try with a 2 ohm atty. At fresh off the charger a 1.5 ohm at 4.2v is satisfying, but that subsides fairly quickly.

 

[Boothvilleboi]

I like my 1.5 cisco 306's, compared to the smoktech 1.5 510's, they put out far superior TH and vapor. Very satisfied.

 

[mikewill45]

Yeah may be time to get a kick again. I did not like the killing of the battery life I had with it in the past. Provari lasts much longer at the same wattage. Wish people would invest in improving manufactured attys, and not just rebuildables. Almost seems like the off the shelf atty is going away. Are the Cisco, Ilenvapes or Hh357s any hotter than a joyetech at same voltage/resistance?

I've used the Joytech, Cisco 306 and the HH.357. I find the 306 superior to the Joytech and the HH.357 superior to the 306.

 

[Riverboat]

I currently use 1.5 ohm joyetech atties in my UFS. I enjoy them for the most part but miss the heat I get with my Provari running at 4.4-4.5 with them. I would prefer to buy atties instead of using RBAs. Anyone know anyone that sells atties at 1.1-1.2 ohms? Or any atties that might produce more heat at whatever ohm?

If you really want a HIGH performance atty, give up the Joyes and buy a HH357 atty... Yes they cost abit but so does a Supercharger..
They last a long time and perform like no other.. For you Provari you want to get the 3.0 ohm ones... I run them @ 5.5 volts= 10.08 watts.
The low ohm ones are for 3.7 volt vaping... 3.0 onh attys last much longer and draw less amps....... with better performance on a VV mod.
Custom HH.357 Cisco Spec Hybrid 510 Atomizer - Avid Vaper
It will take your vaping to a new level..... and them some....

 

[Riverboat]

I've used the Joytech, Cisco 306 and the HH.357. I find the 306 superior to the Joytech and the HH.357 superior to the 306.

Someone knows the truth.....HH357