• This forum has been archived

    If you'd like to post a thread, post it here instead!

    View Forum

Mech Mod Questions

Status
Not open for further replies.

phonefix

Full Member
Verified Member
Jul 12, 2011
44
0
Singapore
Hey guys.

I'm quite puzzled if dual coils can be used on a mech 3.7V mod.
Would higher resistance be more ideal for such a set-up or lower resistance?
In the case of 1.5ohm dual coil cartos in a tank, should that be considered as a 3ohm device?

Do share your thoughts. SafeVapingPowerChart.jpg
 

Alfro

Senior Member
ECF Veteran
Verified Member
Jan 25, 2013
118
50
WP,PAP
Yes! dual can be used on mech mod. why not?

Hmm let me try to put this into picture, hopefully you'll see it with much better understandings.

3.7v IMR Batteries = Voltage Current (imagine this as 1-way water current)
Coil = Carrier. "Straw / Water pipe" ( now imagine this pipe get plunged and start drawing from the water current)
Ohm/Resistance = The results aftermath (ie. the smaller the diameter of the pipe or the longer it is from its destination, the greater the resistance is experienced for the current to gush through and vice versa)
Single coil > 1 Straw/Pipe
Dual > 2 Straws/ Pipes
Quad >so on n so forth..

If you'd get the drift, setting up dual coil will force the nature of the current to go into split channels. With that in place, dual setup results in much lower ohm readings/resistance due to the split. But, more current is required to push through to meet both ends. In another words, what you get is simply both the wicks evaporating juices at the same time, thus double the taste/vape. But, battery will be drained out in a much much faster rate.

Highly doubt one could get 3ohm on a dual. Unless super high 35-40gauge wire and ridiculously lotsa rounds this coil is clocking. ;)


PS: always use a ohm reader to test the atty/carto before sucking on them! and duncha follow blindly on the table. its like a parental guidance thingy. lol
 
Last edited:

phonefix

Full Member
Verified Member
Jul 12, 2011
44
0
Singapore
Yes! dual can be used on mech mod. why not?

Hmm let me try to put this into picture, hopefully you'll see it with much better understandings.

3.7v IMR Batteries = Voltage Current (imagine this as 1-way water current)
Coil = Carrier. "Straw / Water pipe" ( now imagine this pipe get plunged and start drawing from the water current)
Ohm/Resistance = The results aftermath (ie. the smaller the diameter of the pipe, the greater the resistance is experienced from current to gush through and vice versa)
Single coil > 1 Straw/Pipe
Dual > 2 Straws/ Pipes
Quad >so on n so forth..

If you'd get the drift, setting up dual coil will force the nature of the current to go into split channels. With that in place, dual setup results in much lower ohm readings/resistance due to the split. But, more current is required to push through to meet both ends. In another words, what you get is simply both the wicks evaporating juices at the same time, thus double the taste/vape. But, battery will be drained out in a much much faster rate.

Highly doubt one could get 3ohm on a dual. Unless super high 35-40gauge wire and ridiculously lotsa rounds this coil is clocking. ;)


PS: always use a ohm reader to test the atty/carto before sucking on them! and duncha follow blindly on the table. its like a parental guidance thingy. lol

Right on Alfro, i got u.
Tks mate.
 
Status
Not open for further replies.

Users who are viewing this thread