Mech Mods

[elevensev7n]

hello, i have a question about mech mods and i hope you guys can clarify it.

Does every mech mod have 0.1 ohm support or i have to search for one specifically?

im planning on buying the vandy requiem, thanks in advance for the replies!

 

[Shawn Hoefer]

True mechs are just a battery/cell, an atomizer, and a switch. Their "support" of any given resistance is based not on the mod, but on the cell used. Your best bet will be to learn your ohms law/watts law, and run a calculator before using. For instance, your hypothetical 0.1ohm build on a mech with a fresh cell will draw 42 amps. There are no cells to my knowledge used in mechs that have a 42 amp rating. Better to build a little higher. While you're at it, make sure that the cells you get/have are properly rated from a reliable source.

 

[Izan]

hello, i have a question about mech mods and i hope you guys can clarify it.

Does every mech mod have 0.1 ohm support or i have to search for one specifically?

im planning on buying the vandy requiem, thanks in advance for the replies!

Hi and welcome,
I have the VV Requiem kit with the "dark" version of the RDA.
A mid range build ~.2Ω-.25Ω with a decent 18650 (molicel P26a) should last between refills of the stock bottle.
Squonker= 7/10. Needs a tweak or three, IMO.
RDA (requiem dark)= 3.5/10. LOUDLY Whistles (wife forbids use in her presence). No standard 510 pin, only BF pin included. It whistles loudly. Need to remove an o-ring to get the top cap off without tools. 0/10 over-squonk tolerant. BF pin above base level, base doesn't drain. And it's annoyingly loud...did I mention that?


Where are you located?
How long did you smoke and how many per day?
Do you have experience with mechs and rebuilding?
Will this be your first RDA/RTA/RDTA?
Your first squonker/mech?

What are you using currently?

Welcome to the ECF.
I

 

[BrotherBob]

hello,

Welcome and glad you joined.

 

[smacuser]

Welcome to ecf @elevensev7n

Mesh mods are only how you make them. I don't have any real experience, but I hear the lower you go, the more you know.

 

[Territoo]

Welcome to ecf @elevensev7n

Mesh mods are only how you make them. I don't have any real experience, but I hear the lower you go, the more you know.

The more you have to know before they blow.

 

[smacuser]

The more you have to know before they blow.

 

[Ed Brown]

your hypothetical 0.1ohm build on a mech with a fresh cell will draw 42 amps.

and you'll be vaping at 168 Watts. Too hot for me!

 

[denali_41]

most any mec will handle .1 build,but lower the build the higher the arc jump which pits the contacts faster

and then theres the battery capability ??

remember you are putting that up to your face

 

[smacuser]

He's dead.

 

[Territoo]

 

[Skeebo]

He's dead.

 

[ShowMeTwice]

 

[Ed Brown]

I hate it when the OP just disappears.

 

[Territoo]

I hate it when the OP just disappears.

That happens more frequently than not. I bet maybe 1 out 20 new members stays on the forum.

 

[somdcomputerguy]

Welcome to ECF, elevensev7n.

 

[Coyote628]

Welcome to ecf @elevensev7n

Mesh mods are only how you make them. I don't have any real experience, but I hear the lower you go, the more you know.

How low can you go. All I know is what I know.

 

[Kprthevapr]

His battery might have 'sploded

 

[Rat2chat2]

Don't leave yet. . . I still want to welcome you to ECF.