Mix 80 by Artery

[Tpat591]

I understand Artery managed to release the Mix 80 and further release Nugget V2.0, Nugget Pro, Mix 150, Ginger, Archer Kit, and Trace tank before the 8/8 cutoff under the radar. Apparently they are getting away from proprietary usb cables they used in the original Nugget and have incorporated a replaceable 18650. It supports Ni200, Ti, Stainless Steel, TCR, Power, & Voltage Modes.

 

[Tpat591]

ARTERY MIX 80

ARTERY MIX 80 KIT

“Mix 80” Kit by Artery – FullTankVape

 

[Tpat591]

 

[Tpat591]

 

[Tpat591]

 

[Tpat591]

Mix 80 was first released to the market on 8/8 in limited quantity and full production release occurred on 10/8.

Nugget Pro was also released on 8/8 in limited prototype quantity. Nugget Pro will go into full production release in approximately two weeks time.

 

[BobC]

I guess you're the only one interested in these devices, friend of yours?

 

[Tpat591]

Artery device may not be the most refined, pretty or even capable devices on the market, but they are very well built, sturdy, and reliable. They are improving their TC and guis and for a small company their devices are damn respectable.

 

[Tpat591]

 

[Tpat591]

 

[Tpat591]

 

[Tpat591]

Artery Mix 80W TC Box Mod $35.99 - VAPE DEALS: Vaping | Vape Mods | E Liquid | Ecigs

 

[Tpat591]

 

[Tpat591]

 

[Tpat591]

 

[Tpat591]

Attached is a PDF of the Mix80 Instruction Manual Above

 

[Tpat591]

 

[hazozita]

I got my Mix-80 in the mail today. Need to use it for a while longer before passing final judgement, but so far it's been excellent. I got the two-tone model (white case with a black battery door) which looks very nice. Fit and finish is great for the most part. The only issue is a slight wiggle to the battery door. The white portion is glossy but does not show fingerprints, which is a welcome change.

The menu system is reasonably straightforward, although I need to play around with it a bit more to figure out the PMG mode. It's been fine in regular wattage mode, and is performing very nicely in TC mode with Ni.

No regrets at all (so far, at least!)

 

[Tpat591]

PGM mode is Kanthal Preheat. It allows you to adjust the multiplier for your wattage setting during the first 2 seconds of the vape. It does not apply to TC.

• Upon entering PGM A, B, or C, one reaches a screen that allows adjustment of two variables.
  
• The First is Sec. & Next is Mult.
  
• Sec. are in 0.1 increments from 0.1 - 2.0 Sec & advanced by pressing the [Fire] button.
  
• These Sec 0.1 increments appear to be slices of an overall 2.0 Sec. Time Frame.
  
• During each 0.1 sec slice, you appear to be able to adjust a multiplier to your wattage setting by pressing the [+] & [-] buttons.
  
• By Adjusting this wattage multiplier for each 0.1sec slice over the entire 2.0 second time frame a user can define a preheat curve to be applied to the Kanthal coil you are vaping on.
• When you have defined the entire time frame, press & hold the fire button to lock in the program.
• Thereafter entering the program setting you will adjust your wattage to maintain proper vaping temperature of the coil after the pre-heat without overheating the coil.

 

[Tpat591]

Received a black & a white Mix 80. Hadn't realized that you could order one actually Mixed. Nice sturdy, well styled mod with plenty of power. Very impressed. Artery is getting better. Did you have a firing delay before update, I haven't updated, but have noticed no delay.