this idea has been bugging me for sometime
i plan on a 3.7v and 5v mod in one using a two way switch,
using this booster TPS63002 from ti
focus.ti.com/docs/prod/folders/print/tps63002.html#technicaldocuments
(cut and paste this and add http:// to see the specs)
plan on getting it from digi-key
search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=296-19644-1-ND
(same part but if you want to see do the same thing)
i planed on a single 14500 cell to power this but looking at this booster i wonder if wiring to 14500 together in a parallel would work for this...
well still up in the air about the box or switch, but haven't looked up what kinds of caps to use (kinda dont know where to start there...)
well for the 3.7v side it would be a simple wire job going through the two way switch, and the 5v side wired through the booster to the switch, so the 3.7 and 5v are wire in parallel in the box or whatever body used and each side would work on there side of the two way switch. so switches between them at will without much to deal with. but still trying to figure out if this thing has a control to wire a tact switch for another mod idea... it work work with this on cause the 3.7v wired into the switches 1A to 2A going through them so i need a 2A switch for this idea... i know connman (?) made something like this way back when (read to like page 67 on this forums or i saw something like it some where lol)
this next idea i just came up with not even a few hours ago.... (was inspired by talking bout the idea above with cskent in the new members forum... who made this new member very welcomed in this forum)
i can picture form it is a puck style 2x 4xaa batt box (or any other box you can fit four batts in) mod have two of the four 3.7v batts wire in a sires though the regulator (for higher volt vaping...) into a two way switch (or three way switch for the off), and the wire the last to batts into a parallel wire to its respective side of the switch for 3.7v vaping... its two completely different batt set up in one mod...
any input is welcomed... (fyi, these are mods i plan to do in the future but as of now ill stick to simpler ones till my soldering skill get up there lol)
thank you
a noob
i plan on a 3.7v and 5v mod in one using a two way switch,
using this booster TPS63002 from ti
focus.ti.com/docs/prod/folders/print/tps63002.html#technicaldocuments
(cut and paste this and add http:// to see the specs)
plan on getting it from digi-key
search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=296-19644-1-ND
(same part but if you want to see do the same thing)
i planed on a single 14500 cell to power this but looking at this booster i wonder if wiring to 14500 together in a parallel would work for this...
well still up in the air about the box or switch, but haven't looked up what kinds of caps to use (kinda dont know where to start there...)
well for the 3.7v side it would be a simple wire job going through the two way switch, and the 5v side wired through the booster to the switch, so the 3.7 and 5v are wire in parallel in the box or whatever body used and each side would work on there side of the two way switch. so switches between them at will without much to deal with. but still trying to figure out if this thing has a control to wire a tact switch for another mod idea... it work work with this on cause the 3.7v wired into the switches 1A to 2A going through them so i need a 2A switch for this idea... i know connman (?) made something like this way back when (read to like page 67 on this forums or i saw something like it some where lol)
this next idea i just came up with not even a few hours ago.... (was inspired by talking bout the idea above with cskent in the new members forum... who made this new member very welcomed in this forum)
i can picture form it is a puck style 2x 4xaa batt box (or any other box you can fit four batts in) mod have two of the four 3.7v batts wire in a sires though the regulator (for higher volt vaping...) into a two way switch (or three way switch for the off), and the wire the last to batts into a parallel wire to its respective side of the switch for 3.7v vaping... its two completely different batt set up in one mod...
any input is welcomed... (fyi, these are mods i plan to do in the future but as of now ill stick to simpler ones till my soldering skill get up there lol)
thank you
a noob
