Remember the watts takes your ohms to figure out what voltage to use, for me tho I couldn't vape anything at 4 watts, with my hybrid I avg 11 watts
MVS Giveaway thread !!!
- Thread starter aasupplyny
- Start date
- th_trl_thread_readers 0
- Status
I've been using 7-8.5 watts in RMS (02) mode on my Vamo, with 2.2ohms carto tank, and somewhere around the same when I use the 1.2-1.3ohm RBA (sometimes depending on juice flavors, I up this to 8-10 watts though).
When I hit it hard or multiple times in a row, I can feel the battery get hotter much easier with the lower ohms, so I assume this drains the battery much faster right?
When I hit it hard or multiple times in a row, I can feel the battery get hotter much easier with the lower ohms, so I assume this drains the battery much faster right?
yea if the battery is getting hot it is working hard and draining fast.. i use less watts with low ohms and more with higher ohms.. i vape at 3.9 or 4 when using 1.6 ohm and 5 at 2.2 or higher ohms
Hmm, do you think I should try lower watts then? I've tried a little lower, maybe 6 or so, but never real low so not sure how that would affect my vapor or juice tastes. I know it's all about what we like, but now I'm wondering if I'm overvolting things from the get-go with this Vamo 
well ive never had anything that went that high so i couldnt tell you.. but i look for the lowest setting that still gives me the vapor/throat hit im looking for. I think it gives me more flavor, but thats just me
You are talking watts right, not volts? I am, not sure at all what volts those would be.
What PV do you use?
What PV do you use?
Good Morning everyone. I have fallen behind. Darn snow.
I still don't have my RBA up and running. It's interesting reading what you all have to say though.
I still don't have my RBA up and running. It's interesting reading what you all have to say though.
Morning Gang! Just placed my first order with MVS Last night. About time too considering how long I've had a presence in this thread!
Hey Aurora... On this RBA aasupplyny handed out recently... I tried taking the O ring off the top plate, but it made no difference in getting the air hole to line up... I had to sand the cap down. I'm not fully lined up yet... more sanding to do, but it has made a huge difference in the hit!
Also, on my Vamo (in RMS ALWAYS), I run my 2.5 Vivi between 8 and 9 watts, I usually adjust down the longer into the vape session I go... and my 1.4 MVS RBA between 6 and 7 watts.
I've never noticed my battery getting hot. The tube gets warm, but that's just the heat of my clutching the Vamo and never putting it down! I love that thing!
Hey Aurora... On this RBA aasupplyny handed out recently... I tried taking the O ring off the top plate, but it made no difference in getting the air hole to line up... I had to sand the cap down. I'm not fully lined up yet... more sanding to do, but it has made a huge difference in the hit!
Also, on my Vamo (in RMS ALWAYS), I run my 2.5 Vivi between 8 and 9 watts, I usually adjust down the longer into the vape session I go... and my 1.4 MVS RBA between 6 and 7 watts.
I've never noticed my battery getting hot. The tube gets warm, but that's just the heat of my clutching the Vamo and never putting it down! I love that thing!
I played around with mine one day and didn't get it right.
Sometime today, I hope to get the courage to try again!!
Well I tried again...still at about 9 ohlms. 
I have unscrewed the things on the center post enough that it has moved. Is part of the post suppose to be poking up over three little screw on things? Or should it be even?
Good thing I can be stubborn!! I will try again later.
I have unscrewed the things on the center post enough that it has moved. Is part of the post suppose to be poking up over three little screw on things? Or should it be even?
Good thing I can be stubborn!! I will try again later.
Ya I guess you would need lower ohms then, do you plan to get larger Kanthal wire sometime so you can try lower ohms?
Hope you don't get buried too deep! Wish we had some now
Ya, I just noticed that too about the o-ring, stops in the same spot with or without the o-ring for me too! Guess I'll have to file and sand it down!
Maybe I'm using too many watts then? And I think some of the heat I'm noticing may just be because I'm still new to vaping, and was basically a chain smoker, so I'm still chain vaping a bit more than usually probably
Plus, some of it could also be due to the battery I'm using? I grabbed one of the cheap joytech 18650's when I ordered mine, still need to get a better quality battery when I can afford it.Also, I have both springs in the bottom of my cap, does that matter in regards to the heat possibly? Should I remove the smaller one and just use the larger new one that came with it?
I played around with mine one day and didn't get it right.
Sometime today, I hope to get the courage to try again!!
Good luck jj2, keep at it and you'll get it!
good afternoon. I have fallen behind and it has nothing to do with snow. No snow here. This is east texas. I am just..... lazy, I think. LOL
I better go try to get something done.
Now admit it Morri....you are like me. You have spent too much time at ECF and didn't get much done. Yes I'm guilty too.
Well that's good and glad to see you awake mogi.
I will keep trying here and there but don't want to get frustrated at it.
Patience has it virtues.
I will keep trying here and there but don't want to get frustrated at it.
Patience has it virtues.
Merry christmas jj2 you have an open circuit.. there is a difference between 9 ohm and a 9.9 reading 9.9 means open/ incomplete circuit..
9.9 means open/ incomplete circuit..
- Status
