My answer to a pocket friendly dripper

[fogcreature]

I love the flavor drippers produce. After tons of clearos, gennys, cartos, carto tanks and everything in between, i always returned to my 8$ phoenix dripper from DV. I decided that if I'm going to enjoy vaping enough to continue it and not return to smoking I needed to find a dripper that is tough, solid and that the top cap won't pop off of in my pocket but with a larger well than the Phoenix. I have found just that with this monster cloud v2 clone. It has a tall deck, deep well, and is made for quad coils. I think quad coils are overkill, so I've plugged 3 of the 4 air holes with sections of tooth pick and only use a single 1.5 ohm coil with 1.5mm ekowool wick. With a twist of the top cap I can close the atomizer completely. It can be laid on its side as well. All together the walls of this atty are near half an inch thick. I use it with my ehpro ea mod in 18350 mode at work. I keep it in the included drawstring pouch for the ea mod in my pocket in case I over drip. It has a small chamber, great afc, great flavor and multi coil capable. With a little modification it can be a pocket friendly steam machine!

 

[PaulBHC]

Nice, where did you get it?

I was looking at a Stillaire clone from 101vape since it has a slotted outer and inner sleeve for adjustable air. Looks like it could be closed up.

 

[fogcreature]

I got the monster cloud atomizer off of eBay for 40 and the ehpro ea mechanical mod from madvapes for 50. The magma clone looks like it would work too but I like the look of the monster. The magma also looks easier to build on. I'll have a look at the stillaire too thanks for the reply and the suggestion!!

 

[Rat2chat2]

Hey there. I think dripping is the ultimate and after six months of the little igo-L (which I still love) I have started using a rm2 on top of a reo and I can't imagine vaping getting any better for me. Congrats to you and happy dripping. It is all so wonderful.

 

[fogcreature]

Thank you! The rm2 and the stillaire look like great attys. I still don't understand why 99% of rdas have such a small drip well. They all work well though, and if it ain't broke.. I'm glad you've found a great setup too!!! Happy vaping!

 

[juicefreak]

i still drip on my phoenix's. i have about 5 because i drop them so much. they get wonky, but i haven't killed one yet. I like the juice well on yours. will have to check it out! i have an IGO-M on order and i really like the looks of the Origens juice wells. i'm ready for some new drippers, so i'll look into yours

 

[PaulBHC]

I started dripping with old 510 attys and cartos with the filler ripped out. Then I got a $6 A6 and liked dripping. Started getting tired of only getting 4-5 drops and a few puffs and started looking at bottom feeders but didn't find out about the RM2. Ended up with an RSST and like that I can dripp or tank and variety of wicks. But the A6 and RSST will leak out the air hole if laid down that direction.

Still not sure that the Stillare won't seep fluid through the closed air slot. I suppose I could try sliding a vape band clone over the RSST and see what happens.

 

[fogcreature]

That's why I like this one. If I turn the top cap 1/4 of an inch there's no leaking at all. The only time it leaks anything is if I over drip, which would happen on any dripper. I just got tired of losing 5mls of juice when a tank leaked, I'd much rather lose a few drops. The uniform look of this one just does it for me. The build room is limited and you have to get the coil under the top post lip, but it works great

 

[Kimberultra2]

Is the the firing button on the side of the mod? I always wondered what it was


Sent from my iPhone using Tapatalk

 

[fogcreature]

Is the the firing button on the side of the mod? I always wondered what it was


Sent from my iPhone using Tapatalk

It is on this one. It's an ehpro EA clone. Most mods have the firing button on the bottom. I like this button better because I'm using a smaller 18350

 

[meatcarnival]

Stillare leaks pretty bad around the AFC