My mod fires low wattage from what i set
- Thread starter CuriousVaper
- Start date
- th_trl_thread_readers 0
- Status
What sort of make/specification are your batteries? Maybe your mod doesn't like something and is limiting your power?
Did you buy the coils - is 0.13 the reading on the mod for all the coils? Is that about right?
Did you buy the coils - is 0.13 the reading on the mod for all the coils? Is that about right?
My batts are VTC6 as for the coils i had it made from a shop, from where i bought the RDA and they didn't use ohm meter for each coil. Its just now that i noticed.
My batts are VTC6 as for the coils i had it made from a shop, from where i bought the RDA and they didn't use ohm meter for each coil. Its just now that i noticed.
OK - so they fitted the coils and your mod reads 0.13, yes?
I wouldn't expect them to read each coil, but they would usually know the target resistance of each coil.
Is the reading consistent... does it fluctuate at all?
A 3 x battery mod should not complain at a 0.13ohm atomizer.
Weird.
yes it is really weird, i also tried it with TFV12 set it at 100w fired it and reads for only 54.3w, build with kanthal coils it doesn't fluctuate at all.
I'd have to look it up but you may be using to many amps. That resistance at 100w is almost 28a. That is very high you maybe exceeding the limit that it is set for also kind of a dangerous thing. Not sure what the batteries are. You may have the settings wrong in Escribe Manufacturers settings, that is a DNA250 correct. At any rate that is a lot of amperage.
Just looked it up and 54.3 is just above 20a so that may be what the mod is set to fire.
Si you mean the mod fires only at that certain watts because thats the necessary wattage?
Yeah I'm not positive about this the board itself will fire up to 55a but I'm not sure if the battery profile that is programmed in has anything to do with amperage limitation or not. I never really fire anything that high on my DNA's and had to load my own battery profile in. I'm not an expert by any means but I have 4 DNA's. I would go to to this website and ask the question. You'll have to register but people there that really know their stuff about the DNA's and could answer the question.
Evolv DNA Forum
Evolv DNA Forum
How can i load or adjust my battery profile? Im new to DNA boards.
Through the evolve program "escribe".
It didn't come with an instruction / user manual?
It didn't come with an instruction / user manual?
I think i need to re read the manual, uhm on the battery profiles it needs to be manually done? I could set my own preferences? Or is there a guideline to be followed for the a certain batts. Currently uaing VTC6
Depends on what settings / configuration it came from the manufacturer with.
What you have is rather complex compared to most anything else.
It would take me a page to explain, I am
not an evolv fan even though I've owned dozens.
So, I wouldn't be the best person to ask.
There are long running DNA 250 threads in the sub forums & evolve has a forum of their own or google evolv escribe or hopefully it came with decent user manual.
What you have is rather complex compared to most anything else.
It would take me a page to explain, I am
not an evolv fan even though I've owned dozens.
So, I wouldn't be the best person to ask.
There are long running DNA 250 threads in the sub forums & evolve has a forum of their own or google evolv escribe or hopefully it came with decent user manual.
Yeah I got a Lost Vapes Triade 200 and it was all set up except the battery profile which I got from a German website for my LG HG2's the other one I got had the settings that the chip has when it comes straight from Evolve not set for any certain mod but I was lucky enough to find a guy on the Evolve Forum that had done the tests and had the correct numbers for the Mod. You definately didn't get a good mod for new users. They are complicated and once you get the hang of using Escribe work very well but it takes time and studying. Evolve Forum is a great place for info tho.
You need to find a place that has the profile for the battery you are using and download it into escribe then upload it to your mod. Same with wire types. I don't know if it has changed cause I bought my 2 LV DNA's a while ago but the stock profiles they had for wire like Ti, SS316L were way off and didn't work for crap. I used the ones off of Steam Engine. They also,the CSV's have to be downloaded to escribe and uploaded to the mod.
can you help me where i could get those data for my batts? I really confused
Down load escribe on a computer or laptop.
Read the instructions / tutorials, there are some you tube videos on the subject.
Register / join / read evolv's DNA forum.
You've been given the link.
With 3 fully charged cells Run battery analyzer, set wh & csv.
Or you can use calculated wh.
Then go through the other settings & make sure they're set correctly, then set your preferences of options.
You can search through the sub forums
here at ecf for threads about DNA 250's. read & ask questions in threads more specific to DNA 250.
At least some if not most of your questions may be answered by reading DNA 250 threads.
If none of this makes sense use it the way it is while learning about the power device, or use your back up device until you understand how to set it up through escribe.
I'm not trying to be rude, what you're asking is similar to;
'write me a step by step instruction manual on how to use escribe & configure my power device'
Companies that sell these things should provide a detailed user manual or support or a link to evolv for support.
Read the instructions / tutorials, there are some you tube videos on the subject.
Register / join / read evolv's DNA forum.
You've been given the link.
With 3 fully charged cells Run battery analyzer, set wh & csv.
Or you can use calculated wh.
Then go through the other settings & make sure they're set correctly, then set your preferences of options.
You can search through the sub forums
here at ecf for threads about DNA 250's. read & ask questions in threads more specific to DNA 250.
At least some if not most of your questions may be answered by reading DNA 250 threads.
If none of this makes sense use it the way it is while learning about the power device, or use your back up device until you understand how to set it up through escribe.
I'm not trying to be rude, what you're asking is similar to;
'write me a step by step instruction manual on how to use escribe & configure my power device'
Companies that sell these things should provide a detailed user manual or support or a link to evolv for support.
Last edited:
- Status
Similar threads
