My Pipe MOD - The Tough Brass Jr.-TS (Trigger Switched)

[CraigHB]

I love it, it's like if there was ever a nuclear blast, everything would be gone except that mod.

 

[bino]

Here's another "Odd-On" that I am still working on.
I placed my Wicked-Venous Foggy tank mod inside a couple of brass couplings on top of the Tough Brass Jr. Pipe and here is how it looks...

This is still under development though, I'm just excited to share what it should look like and hopefully it would work...

 

[Col. Gaunt]

Oops sorry for the typo Col. Gaunt, it currently runs at 6.4v on a pair of AW LiFePO4 16340s alternating with a pair of generic LiFePO4 17340s and it would probably run at 3.7v on a single 17340 battery plus a false battery...

Sounds good! What type of atomizer are you using on it for the 6.4 volts?

 

[Col. Gaunt]

Here's another "Odd-On" that I am still working on.
I placed my Wicked-Venous Foggy Tank MOD inside a couple of brass couplings on top of the Tough Brass Jr. Pipe and here is how it looks...

This is still under development though, I'm just excited to share what it should look like and hopefully it would work...

Hi Bino, Looks like you are using a 306 atomizer. How does the feeding system work? Are you using a tube on the bottom of the atomizer and drawing the liquid up into it when you inhale?

 

[bino]

I am currently using a regular 306 atty at 2.5 Ohms I think... I haven't tried those high resistance attys yet though...

 

[bino]

Hi Bino, Looks like you are using a 306 atomizer. How does the feeding system work? Are you using a tube on the bottom of the atomizer and drawing the liquid up into it when you inhale?

The Wicked-Venous Foggy Tank MOD (which is inserted in the couplings) functions like a CE2. Its an extra long wicked 306 atty with a cleartomizer tube with side-holes used as a tip, plus a 510/510 extension used as a stem to place it way up near the top of the tank. The wick is inserted through and through the cleartomizer tube and/or under the bridge of the atty. Basically, it is a wick fed system...

 

[bino]

15mm Brass pipe and fittings hold 14500 batteries.
I made this from parts I found at Bunnings (local hardware store) on Friday.
Weighs 180g vs 150g for the Provari.
All up around $15 in parts. Not bad.

View attachment 47712View attachment 47714View attachment 47715View attachment 47716

Thanks tearocks for the suggestion! I hope I could find one of those tubes in one of the local hardware stores back here...

 

[Addicted2Vap]

very very nice.

 

[asdaq]

Nice and shiny, I like them. I'm curious how you go about sanding these, but I bet the answer is 'just do it'. I broke down and got sabre touch parts for all of $7, but they seem too massive to be practical....

 

[bino]

Hi Bino, Looks like you are using a 306 atomizer. How does the feeding system work? Are you using a tube on the bottom of the atomizer and drawing the liquid up into it when you inhale?

Sorry sir if the image above sort of mislead you... Actually, the 306 atty would not be visible when I get this setup working, instead there would only be a 510 or 901 tip left on top, same as my Venous Foggy Tank MOD...

 

[bino]

I am trying to figure out what type of feeding is best for this mod.
The tank type "wicked" design is already displayed above.
The bottom fed one which I will post later...

 

[bino]

I guess I will have to use some silicon tubing to get the juice to the syringe needle beneath the 306 with this set up.

 

[bino]

I finally decided to pursue the "wicked-type" of feeding system instead and so here's another wicked tank design which I came up with and will most likely pursue due to PV size and weight reduction...

This tank add-on is sill based on the Wicked-Venous Foggy Tank MOD only in brass form.
I'll do away with the 10 ml plastic e-juice bottle since I have a hard time fitting it into the pipe.

Now, still with minimal tools needed plus a hammer and a nail, all I need now is a wick, another silicon cap, and a couple of "O" rings...

Vape On!! \m/

 

[eplates]

awesome mod... looks comfortable to hold and vape

 

[bino]

 

[Col. Gaunt]

Hey Bino, I am waiting for you to sell me one of your pipe mods!

 

[bino]

Hey Bino, I am waiting for you to sell me one of your pipe mods!

No need Sir Col. Gaunt, I just posted a D.I.Y. guide on its own webpage. Its integral parts now posted...

Details of components and parts will soon be added...

Please visit The Venous Foggy Tough Mods - Help Desk:
Log In | Facebook

Vape On!! \m/

 

[Col. Gaunt]

No need Sir Col. Gaunt, I just posted a D.I.Y. guide on its own webpage. Its integral parts now posted...

Details of components and parts will soon be added...

Please visit The Venous Foggy Tough Mods - Help Desk:
Log In | Facebook

Vape On!! \m/

I refused to get involved with facebook, can you post it some where else?

 

[mv2envy]

Mario and Luigi want their pipes back!

 

[bino]