• This forum has been archived

    If you'd like to post a thread, post it here instead!

    View Forum

Nebraska Vaping, Part 2

Status
Not open for further replies.

PittBoss

Vaping like a boss
ECF Veteran
Verified Member
Mar 27, 2012
11,961
1,591
Lincoln, NE
I don't want to be premature.....but I think I got it.....i wrapped a new coil......so far all coils are glowing nicely......

I'm thinking that if the mesh is oxidized well, soaked in liquid, coiled around the rope and then a few juice burns.. it should stay on there pretty well. If the edge of the mesh isn't properly oxidized and it ends up resting on the base (around the wick hole) it may short out those lower coils..
 

Jakersvape

Vaping Master
ECF Veteran
Verified Member
Oct 27, 2012
6,795
1,124
43
Lincoln, NE
I'm thinking that if the mesh is oxidized well, soaked in liquid, coiled around the rope and then a few juice burns.. it should stay on there pretty well. If the edge of the mesh isn't properly oxidized and it ends up resting on the base (around the wick hole) it may short out those lower coils..

I'm thinking you may be correct, boss!
So far I haven't had any wicking problems!
 

PittBoss

Vaping like a boss
ECF Veteran
Verified Member
Mar 27, 2012
11,961
1,591
Lincoln, NE
Well, Pitt, did you get all bandaged up and have time to play with the rope?

I have a nice piece cut, mesh cut and wire cut.. One of my DUDs is cleaned out and ready to go.. My small bottle of VG is out.. Meter is out.. Torch is out.. That's as far as I got before getting sidetracked, lol. Didn't even bandage up. I think I'm gonna let it sit out while it's glued. Although, the chunk of skin that is hanging there didn't stay flat as the glue dried, lol. I think if I let that sit for a little bit, it should allow the underneath to heal enough where it will be dandy from here on out!
 

PittBoss

Vaping like a boss
ECF Veteran
Verified Member
Mar 27, 2012
11,961
1,591
Lincoln, NE
So.. It seems I will get on that first thing in the morning. I don't see it taking that long since everything is virtually ready to go! On that note, I'm going to get ready for bed. You have a wonderful night, you dashing wilderbeast!

Oh.. Where the hell has Senor Hawk been today? I'm not complete without him here as well..
 

Jakersvape

Vaping Master
ECF Veteran
Verified Member
Oct 27, 2012
6,795
1,124
43
Lincoln, NE
I have a nice piece cut, mesh cut and wire cut.. One of my DUDs is cleaned out and ready to go.. My small bottle of VG is out.. Meter is out.. Torch is out.. That's as far as I got before getting sidetracked, lol. Didn't even bandage up. I think I'm gonna let it sit out while it's glued. Although, the chunk of skin that is hanging there didn't stay flat as the glue dried, lol. I think if I let that sit for a little bit, it should allow the underneath to heal enough where it will be dandy from here on out!

Well you got part way there! Lol
I bought a meter at menards the other day....it doesn't work the greatest. I have to hold the probes perfectly still and it still seems to jump around a lot.
You should just rip that chunk of skin off....:eek:
 

Jakersvape

Vaping Master
ECF Veteran
Verified Member
Oct 27, 2012
6,795
1,124
43
Lincoln, NE
So.. It seems I will get on that first thing in the morning. I don't see it taking that long since everything is virtually ready to go! On that note, I'm going to get ready for bed. You have a wonderful night, you dashing wilderbeast!

Oh.. Where the hell has Senor Hawk been today? I'm not complete without him here as well..

I was just wondering where he was.....i miss him so! This place just isn't as classy when he's not around!

I'm jealous of Leia! We should have just snuck in the back of her car when she wasn't looking!

Good luck with your wick tomorrow! Mine is still going strong.....so far.

Good night, sweet pea!
 
Status
Not open for further replies.

Users who are viewing this thread