Neo Reo and RM2, Frustrated! Please Help.
- Thread starter jklotz
- Start date
- th_trl_thread_readers 0
- Status
Yeah, see if you can pull it out a bit. Also,,and I'm sure you checked this but make sure the tails from your coil (if you left any on the back side of the post) aren't touching anything but the post.
Here are some build links to help from Supe's sticky on help topics:
Easy RM2 Cotton Build Photo Tutorial - RM2 / RBA 2.0 / Reomizer 2 Rebuild Tutorial
Easy RM2 Cotton Build Video Tutorial - REOmizer 2 / RM2 / RBA 2.0 Build To Get You Started - YouTube
If you make your builds like in the pics and vid, you should be golden.
Easy RM2 Cotton Build Photo Tutorial - RM2 / RBA 2.0 / Reomizer 2 Rebuild Tutorial
Easy RM2 Cotton Build Video Tutorial - REOmizer 2 / RM2 / RBA 2.0 Build To Get You Started - YouTube
If you make your builds like in the pics and vid, you should be golden.
that is my take also.. sometimes an airlock can occur and you must take off the bottle and put it back on.. squonk it without the atty on and make sure juice is coming up in the connector..
OK, thanks for all the help guys. I will try all of the above. BTW - It is squonking fine, at least plenty of juice is going upstairs. Plenty of juice up there, as I've flooded it several times trying to troubleshoot.
I am not ruling out user error by any means, but is it possible my RM2 is a dud, or possibly needs repair? Just wondering, because I've got 2 Kayfuns, a Kayfun Lite, a Taifun GT and an IGO W, all of which I've managed to coil and wick without issue. I'm not new to rebuildables, just to Reo's.
Thanks!
I am not ruling out user error by any means, but is it possible my RM2 is a dud, or possibly needs repair? Just wondering, because I've got 2 Kayfuns, a Kayfun Lite, a Taifun GT and an IGO W, all of which I've managed to coil and wick without issue. I'm not new to rebuildables, just to Reo's.
Thanks!
It sounds like you went through a few builds so it doesn't seem likely but make sure that with ejuice you are not getting any hot legs on the coil. That will give you the burny taste you describe even with a sufficiently juiced coil.
Yeah, it's possible, we're just trying to help you get the best experience out of your new Reo. Seems your problem has stumped quite a few of us so (I'm) basically thinking out loud.
Again, your help is most appreciated! Thank you guys so much.
I am going to try one more build before I go to bed (this will make 6) using some silica and not letting any wires touch, as Rob suggested. If that doesn't work, I'll see if Rob has any possible solutions.
Thanks again guys, you all are awesome!
I am going to try one more build before I go to bed (this will make 6) using some silica and not letting any wires touch, as Rob suggested. If that doesn't work, I'll see if Rob has any possible solutions.
Thanks again guys, you all are awesome!
I don't know but if you use a 5/32 drill bit to build your coil, isn't that a little too big ? That's like 4mm in diameter. I usually only uses 1/16 or 5/64 that's only 1.6 - 2.0 mm in diameters for my micro coils . Your coil looks really "fat' compare to mine . Just my 2 cents . Good luck !
Last edited:
Now that I think about it, that would also be a hell of a lot of cotton in there... Or... Not enough?
Here are my 2 cents and what's gives me a very satisfying vape on my RM2 and VA Cyclone
1. Wrap around a 1/16 or 5/64 bit as recommended above
2. Try an ugly spaced coil... you can do 6 wraps for about 1 ohm
3. Bring you coil to the outer edge of the deck and ensure it's right near the airhole.
4. Use less cotton with short legs and just enough to reach deck near the squonk hole
I believe you are NOT getting enough air in to cool your coil thus causing the dry hits (burnt taste). Just make sure your coil is NOT touching the RM2 cover either.
1. Wrap around a 1/16 or 5/64 bit as recommended above
2. Try an ugly spaced coil... you can do 6 wraps for about 1 ohm
3. Bring you coil to the outer edge of the deck and ensure it's right near the airhole.
4. Use less cotton with short legs and just enough to reach deck near the squonk hole
I believe you are NOT getting enough air in to cool your coil thus causing the dry hits (burnt taste). Just make sure your coil is NOT touching the RM2 cover either.
- Status
Similar threads
