NEW avs3 (UFS)

[Wylie]

Thanks mate..
That was pretty quick..

I wanted to buy a steel mouthpiece but it got sold out by the time I made up my mind

That was from my first UFS. My second run UFS is on its way (expected delivery is Monday). There's no time for thinking when you're buying one of these babies!

 

[ken729]

I'm having a slight issue with my UFS. It seems to be unscrewing the atty when i close the CR all the way. Anyone experiencing this? Am i doing something wrong?

 

[Wylie]

Look back on page 28.

 

[imeothanasis]

Screw hard the atomizer to the connector and dont screw hard the mouthpiece to the cap ken.

 

[ken729]

i'll try that. thanks!

 

[imeothanasis]

Anytime buddy. And dont forget to put a little vaseline to the o-ring of the cap

 

[shamreez]

Hi All,

Got my UFS today and here I am with my first doubt.

1) I took apart the UFS
2) Applied Vasline
3) Put it back filled with juice

But when I am trying to vape I am not able to get any draw (Even with the air holes fully open)
If I try to draw real hard I get bucket loads of juice in my mouth.

Would any of you be able to tell me what I am doing wrong..

 

[Caddyman]

Make sure the liquid is closed off, turn to left like left loosy.

Make sure air is open, same thing, left, so you can see the 4 air holes.

If it is still blocked post back

 

[shamreez]

I tried it..

I removed the complete liquid
closed up the UFS and opened the air holes fully but when I am trying to take a drag it seems like the air vent is blocked

Did not have much time to play with it also will have to try it once more in the evening to see what the problem is

 

[Caddyman]

Check the base of the atty connector, where it threads into the cr at the bottom. There should be 4 holes around the base of it, right above the threads, if they are not drilled through you will get this situation. Some ufs were faulty when created and shipped. If this is the case contact the vendor you bought it from for a replacement.

The only other person i know of that got one like this is me.

 

[shamreez]

Will check that in the evening..

Thanks a lot caddy...

 

[Caddyman]

No prob, here is a quicky sketch, look for the holes and make sure they are drilled all the way through.

 

[Poppa D]

Maybe this will help, my 4 air holes were plugged with shaved rubber from the O Ring at the control ring, so no air could get through. I took a sewing needle and cleared them, I got air now.
Good Luck Shamreez

 

[shamreez]

Maybe this will help, my 4 air holes were plugged with shaved rubber from the O Ring at the control ring, so no air could get through. I took a sewing needle and cleared them, I got air now.
Good Luck Shamreez

Well I do hope that a sewing needle would solve my problem
Coz I would dread to send it to get it repaired and wait again....

 

[stitosma]

Mine were plugged too, but I don't know what it was. Hard black stuff. All is great now!

 

[shamreez]

Dont know if it is me or something wrong with my UFS.
Took it down completely cleaned it nothing blocking the vents.

But when I put in the mouth piece it is like the complete draw is blocked.
If I take a draw too tight liquid comes up in my mouth.........

Not a good time I guess since Imeo has also left for holidays....

 

[shamreez]

As you can see in the image above.
Once I remove the bottom pin I can get a smooth draw but if I put in this pin than the draw gets completely stuck..

And I cannot use the UFS without this connecting pin also right

I can see three rings also there..
I am not exactly sure where this rings go..

Would any of you be able to help me with this information

 

[Poppa D]

Did you check the 4 holes (all in a row) under the air control ring? Mine were plugged.

 

[shamreez]

Yeah the holes seem fine.

I am not sure where the o rings shown in the pic above goes..

Does it go in the pin from the inside of the atty connector or on the outside as a cushion between the atty connector and the pin

 

[Caddyman]

everyone seems to be talking about the holes at the air control ring, im talking about the holes in the base of the atty connector

that is what my defective one looked like, score marks where the holes should be drilled through to the center post.

you should be able to put your mouth over the disassembled atty connector piece, with the center post in, and pull air easy.