RDA New GeekVape Tsunami 24 Includes BF Pin

[Roadtrip635]

I just saw this a few minutes ago, but the new Tsunami 24 is going to include a separate BF pin. It looks like a nice option for those that want a BF atty capable of handling bigger builds. It has a nice big build deck and even comes with some nice premade coils. It's nice to see more options coming out, hopefully more companies will still including a BF option. It does have airflow for single or dual coil options.

I think this would work nicely on the new Kanger Dripbox 160TC

 

[Izan]

Looks cool...
If it is ANYTHING like my Freakshow mini...over squonking produces a HUGE mess.
On a liquid sensitive mod (read regulated) I'd prefer something with a top air feed system.
YMMV
I

 

[muzichead]

Depending on how high the pin is drilled. If it is deck level so it can empty properly it is a positive... If it's not deck level and it is unable to empty completely then it is a fail... Kinda like the raised positive posts you are seeing in a lot of 2 post atty's now days... Fail all the way round for BFr's...

 

[Rex Everything]

I have a BF 22mm tsunami that I got from Apex and leaking hasn't been an issue thus far....getting use to such a big atty (usually us Stumpys,deringer, or tugboat with slam cap) has been more difficult.... couldnt even imagine what to do with a 24mm

 

[hildicat]

I don't see a slightly raised bf pin to be a problem. Especially with large atties that are run at high watts, I like to have a little juice left in the well after a squonk.

 

[Roadtrip635]

I don't see a slightly raised bf pin to be a problem. Especially with large atties that are run at high watts, I like to have a little juice left in the well after a squonk.

I don't think it would be too much of an issue either, especially considering how large the atty is. I would expect it to be a little longer since the pin is fully adjustable and should be to accommodate different mods. It shouldn't be a problem to file down the BF pin if needed. I was hoping to find some real pics of the BF pin installed, but haven't seen any yet. These were the only real pics, instead of renderings, I have seen so far

Heaven Gifts has them for pre-order right now. Another cool thing about HG, is that they also carry GeekVape accessories and replacement parts. I've seen replacement pins for the Griffin and Avocado, as well as the nice hardened hex screws etc. there, so I would guess they will eventually also have replacement BF pins too.

 

[muzichead]

The problem with a raised feed/drain hole, positive post, or positive pin is that it will leak when carried for work. I am a handyman by trade and from one minute to the next I could be going up a ladder, climbing, crawling, upside right, upside down....get the idea? This 100% of the time causes a problem with leaking... I don't care what atty it is. All I know is an atty that drains completely doesn't leak as bad, if at all and the ones drained high leak like a sieve... Thats just my ...

 

[tpedwards]

I don't see a slightly raised bf pin to be a problem. Especially with large atties that are run at high watts, I like to have a little juice left in the well after a squonk.

Fully agree I've had mine for a week now. Bf pin sticks out a fair bit, no problem at all with leakage. Carry my squonker in my pocket all day. I think because your coils are so high you need a bit extra juice to keep your cotton good and wet.probably not the best choice of words there.

 

[Car147]

I have had one a couple of days and it's very good. Currently squonking at 46w on the lost Vape Halycon DNA200 SS316L coils @.40 ohm

 

[Car147]

Now been using it for over a week and i am impressed, still running it on the Halycon at 50w with SS coils. Never had a leak, and if you like a good airy draw this atty hits the spot.

 

[cheeseofvapes]

damn 24mm squonk atties?? gonna chuck mean cloudage! this looks fun for some nice high wattage squonkin!!

 

[Taowulf]

I've had mine a few hours, already loving it.