NEW YIHI SX MINI ML CLASS!

[Moto-EC]

60J @ 520F is what this guy is doing.... he locked resistance at .055 ohm I think... here is the video....

and another..

Thank you I had seen the first video before I purchased it that's why I was jazzed to get one. I had set it up at his settings once but it burnt to. After watching the second video I have been in Joule mode which I guess is wrong? I'm a little confused because the 2nd video he says to really ramp the power down 60 watts. The first guy is at 525F 60j which is high to me. Specially on a single 18650. I'm going to get back at it and see how I do.
I'm going to Rewick again to see if I can beat the leaking issue I had. This all will take time! Thanks for all the help Guys I really appreciate it! Keep it coming!

 

[Moto-EC]

My coil reads 0.058 I'm having to adjust it to 0.064 to get a good vape

Are using the ML then? In power mode? Temps or settings please? Thanks again!

 

[Jake67]

I ran 1 tank through which didn't take long at all because this tanks drinks juice faster than my crown tank.
Wicking was super simple and I had no leaking on the first tank. I filled to 3/4 full. Second tank I filled to the top and I did experience some leaking but not much. Joules mode was a complete fail for me but I haven't made many adjustments. The dry coil came on almost immediately.
In power mode the Flavor was great at 45 W. The battery sag is significant but to be expected with such a low resistance. The tank gets very warm and stays warm for quit a while.
Airflow is very wide open , I'm more of a MTL vapor and found it too wide open. The airflow is extremely turbulent.
So far I'm really on the fence with this tank.


Sent from my iPhone

 

[David247]

Hi in all three videos the elements are different mine looks like the one in the second video retird posted
my settings for ipv5 are 27 joules 400f 0.064 ohm I have to agree with Jake67 on this tank

Regards David

 

[Moto-EC]

Ok I got up today thinking I should write something positive about this tank. I like the drip tip, the build quality is very nice. Its a solid tank. For you guys that Like a ton of air flow it has that. I myself wish when shooting for a design with a lot of air they could have a lower setting for those that don't like as much(Not just this tank).
Then I tried to run it in power mode as suggested at 45 joules and it was still a burnt taste. I turned it down to 22 watts and that was better but I couldn't go much higher. It was still weak.
I went to refill again(Top) and it leaked again. I barely went over the top of the atomizer(top cap of the coil head). I went back and reread the instructions again. above the Spec's tab it lists this as a 2ml tank. The picture shows (after really looking at it) That you only fill it to the top of the atomizer. I guess the smaller X2N's difference is it doesn't have the huge wasted space that this tank has? It's listed as a two ml tank. I really bought this at my own risk because it was so new but Dam! Im with you guys, on the confused Fence!!

 

[David247]

I haven't had a problem with leaking been able to fill up to the holes on top

 

[Moto-EC]

I haven't had a problem with leaking been able to fill up to the holes on top

Wow! That's great. I guess my wicking isn't good as I thought? I'm not giving up on it yet.

 

[Rockwell222]

Hey everyone I haven't been on here since I found that 99$ deal for the ml class. I got the flu for 3 weeks then right after got some throat cold for 5 days. It's been a awesome month lol. In the past couple months I've been using my mechs and just today I figured I'd try my petri on my ml class but it ohms out at .12. I tried it and it works perfectly fine in power mode at 75 watts. I thought it could only fire .15 and up in power mode so I was wondering if anyone else has noticed this. I know some devices soft limit but this doesn't seem to be doing that but who knows I'm not to great with electronics. Any info would help but as of now I'm loving using my ml class instead of my trusty mechs.

 

[VapeGodExclusives]

Haha trusty mechs

 

[GccTxs67]

Dang!

Ferrari Red limited edition...

Sent from my iPhone using Tapatalk

 

[Hyperspace]

Dang!

Ferrari Red limited edition...

View attachment 543516

View attachment 543517

View attachment 543518


Sent from my iPhone using Tapatalk

Wow, if I didn't own a ML already I would be all over that.

 

[Hyperspace]

I see the new red is suppose to be smaller and sell for no less than the mandated price of $219.

Red SXmini ML Class by Yihi - Coming Soon

 

[GeorgeS]

Dang - I hope they make a "Q" in THAT red!

 

[Moto-EC]

Wow I'm stoked! I just got my new stainless Elavated vapes Battery(door) cap!! It's Great! So easy to get in and out of now. Well worth it, plus no moving parts to break. The tolerances are perfect. The gap around the old cap is almost totally gone. Check em out.

 

[Lo zio]

Hi everyone!

I was reading around that firmware 2.206 should allow the X2 tank to be run in Joule mode, is this correct?
And if yes, is it safe to install? I would like to give it a try, just for fun.

And also:

Single greatest enhancement, better then updates, sleeves and logos. So simple and effective.View attachment 535246

Are these battery caps available for purchase as far as you know (in Europe would be nice)?

Many thanks!

 

[Lo zio]

Sorry for the double post, just a heads up to point out to the new firmware, 2.208.

-YiHi SXmini-Innovation for you!

Apparently again with support up to 200W, which was a glitch Yihi already allowed some time ago. Maybe I would leave where it is.

 

[Hyperspace]

Sorry for the double post, just a heads up to point out to the new firmware, 2.208.

-YiHi SXmini-Innovation for you!

Apparently again with support up to 200W, which was a glitch Yihi already allowed some time ago. Maybe I would leave where it is.

I noticed the display is dimmer now with this update. The 200W support isn't a glitch. Perry said it's new to the ML but you need the extension tube to get there.

 

[Lo zio]

I noticed the display is dimmer now with this update. The 200W support isn't a glitch. [...]you need the extension tube to get there.

Yep, I realized that later....
Well, so nice looks out from the box and then this extension tube... I think I'm sticking to 75 W...
A dimmer display isn't that bad maybe, it's pretty bright as it is, even unneccessarily too much.

 

[Hyperspace]

Yep, I realized that later....
Well, so nice looks out from the box and then this extension tube... I think I'm sticking to 75 W...
A dimmer display isn't that bad maybe, it's pretty bright as it is, even unneccessarily too much.

Yeah the extension tube looks ridiculous. I can't imagine anyone wanting to use it. I'm sticking to 75W too. The dimmer display doesn't bother me either because I'm guessing the trade off is longer battery life.

 

[Joe A]

Hi everyone!

I was reading around that firmware 2.206 should allow the X2 tank to be run in Joule mode, is this correct?
And if yes, is it safe to install? I would like to give it a try, just for fun.

And also:



Are these battery caps available for purchase as far as you know (in Europe would be nice)?

Many thanks!

I think I heard they were at a few US vendors, I have no idea about the EU. I'm sorry...