Big and little. I finally scored "THE" topper for the P+ 10 (Mark Bugs Inifity).
Ohhhh where can I get that atty or something a lot like it that you have on your P10???!!!
"Official" Super-T Picture and comment thread!
- Thread starter forcedfuel50
- Start date
- th_trl_thread_readers 0
- Status
Ohhhh where can I get that atty or something a lot like it that you have on your P10???!!!
The Mark-T isn't made anymore, unfortunately. Every so often they show up in the classifieds.
It's my favorite all day every day atomizer no matter what size tube I put it on, but looks like it was made for the 10440. I love it so much I have two now thanks to Mr. Blazer, and yes, I'm selfish enough to keep them both.
Not too shabby... I do have to admit that I immediately liked that mark -T one... Hmmmm any sellers?
.
May I ask where you got that great drip tip? Im a bit of a drip tip fanatic.
Not too shabby... I do have to admit that I immediately liked that mark -T one... Hmmmm any sellers?
There is one in classifieds for $175.
Hi all. im new and I just obtained by precise plus. What's the diff between slanted and flat? Also, can a smoktech or boge kinda tank fit flawlessly without an adaptor?
Is it a PrecisePlus 18? With a flat cap, the outside diameter will remain 20mm. With a slant cap, it bevels to 16mm. So, if you find tanks that are either 16mm or 20mm outside diameter then it should fit flawlessly with the P+.
Example:
16mm OD Spheroid on 18350 slant cap & 20mm OD DID on 18500 flat cap.
Last edited:
Close up of the polished super-T finish. The drip body attached to it is a fairly standard "polished" finish, so I think it shows the differences nicely.
Your pictures are so wonderful.
How do you like the drip body? I just discovered it last night. Do you intentionally overjuice so that you have to drip less - or do you drip the same amount that you would with a drip shield? (Honestly, I don't drip any more with a drip shield than without it, but I know some do). I have rebuildable drippers, but nothing tastes as good as direct dripping onto a 1.5ohm attie. I was hoping the drip body might be the answer for when I'm out out of the house. It looks fantastic on that mod.
Ah! Mines a 18. You're a genius! That was really informative! Thanks much!
Is it a PrecisePlus 18? With a flat cap, the outside diameter will remain 20mm. With a slant cap, it bevels to 16mm. So, if you find tanks that are either 16mm or 20mm outside diameter then it should fit flawlessly with the P+.
Example:
16mm OD Spheroid on 18350 slant cap & 20mm OD DID on 18500 flat cap.
Thanks!! You still don't want to overdrip too much - you can flood it by putting enough liquid in it that the level reaches above the air holes, and then your atomizer is flooded and you get a partially submerged coil - giving you weak vapor until you vape some of it down. You can definitely be more liberal with it, and the best part is obviously not having it leak everywhere. I like drip shields, but I'm just not a fan of aluminum, and most of them don't match my PV's.
I do like the adjustable center pin a lot - I'm going to keep using it for a few days, and I may send it off to be refinished to match my Shockwave a little better.
With that said, it's not light years ahead of a 510+510 sealed extender+drip shield as far as functionality goes. But I'd use it over a standard drip shield any day.
Thanks so much for the feedback, maybe I'll try one out. Why NO ONE makes a straight-sided stainless steel drip shield is just beyond me. I don't use aluminum either.
American Heavy Metal
ShockWave & 2002 Bonneville SSEI
See what you did, Vap ? Even Snork is taking pics inside his car now.
Note how I goosed the tach a bit, but I couldn't figure out how to goose the speedometer.
When I first got my car in '02 it really turned heads. It was my dream car. Still is. Hope I drive it into geezerdom.
- Status
Similar threads
