Pictures of your setup

Status
Not open for further replies.

djenkins

Senior Member
ECF Veteran
Verified Member
Sep 26, 2013
84
80
Albuquerque, New Mexico, USA
My current favorite set up: Semovar with kayfun and Grants Vanilla Custard

Semovar.jpg
 

Nach

Ultra Member
ECF Veteran
Verified Member
Jul 14, 2012
2,407
4,676
48
Chicagoland, USA
jazco.net
Thanks, performs well! Only complaint is that it drains juice. I killed 2 tanks today. Thick plumes however. Built at .72 ohms, dual coil 30 gauge 'auto dripper' with cotton wick, AWIMR battery.

Another pic w/o the drip tip:

How can you complain that it drinks juice for breakfast with that setup?? LOL sub ohms will drink juice let alone dual coils. :)
 

anavidfan

ECF Guru
ECF Veteran
Verified Member
Jun 14, 2012
10,216
20,329
U.S.
Vapemail!

Not exactly a setup, but will make rebuilding a tab easier!

http://i.imgur.com/M5E4jGS.jpg

Sent from my phone with an identity crisis.

I have been tempted to get one of these, but it seems there are so many to choose from. Seems everytime I think I might get one, then I read a review or post that says whichever one I almost ordered has problems.

I wish I knew of one that was consistent so I could order with confidence.

I dont really mind twisting, but with my bad hands it will be hard someday. I make at least 10 wires about once a week, just so Im stocked in case my hands decide to become uncooperative.
 

rojo

Ultra Member
ECF Veteran
Verified Member
Jul 8, 2011
1,162
2,261
Johnson City, TN
I dont really mind twisting, but with my bad hands it will be hard someday. I make at least 10 wires about once a week, just so Im stocked in case my hands decide to become uncooperative.

By the time that happens, you'll have found something you like better than the Ody I bet. Times, they are ah-changin'.
 
Last edited:

MoDmAnDaN

Ultra Member
ECF Veteran
Verified Member
May 31, 2013
1,157
1,103
61
Spanaway, Wa.
I have been tempted to get one of these, but it seems there are so many to choose from. Seems everytime I think I might get one, then I read a review or post that says whichever one I almost ordered has problems.

I wish I knew of one that was consistent so I could order with confidence.

I dont really mind twisting, but with my bad hands it will be hard someday. I make at least 10 wires about once a week, just so Im stocked in case my hands decide to become uncooperative.

I know what you mean! I work IT, and my wrists are usually killing me by days end. I haven't been one to build more than I need, but I think with this, that'll change.

I did quite a lot of research before going with this and couldn't find anything bad about it, plus, it helped that this was the only one I could get my hands on! Lol everything else was out of stock, or still being developed.

Sent from my phone with an identity crisis.
 

qorax

ECF Guru
ECF Veteran
Verified Member
Mar 6, 2013
12,652
41,477
Brampton, Canada
www.facebook.com
I have been tempted to get one of these, but it seems there are so many to choose from. Seems everytime I think I might get one, then I read a review or post that says whichever one I almost ordered has problems.

I wish I knew of one that was consistent so I could order with confidence.

I dont really mind twisting, but with my bad hands it will be hard someday. I make at least 10 wires about once a week, just so Im stocked in case my hands decide to become uncooperative.

Check this out: Wire Welder Piko3 v2
 
Status
Not open for further replies.

Users who are viewing this thread