Pictures of your setup

Status
Not open for further replies.
Been looking at a lot of awesome setups here. Kind of makes me hesitant to post mine, but I need post counts to post and ask question in different parts of the forum, so here we go. Just started vaping about 2 weeks ago and this is my very first setup. Provari mini with DCT Tank & 1.5ohm Carto. The juice (almost empty when I took the pic) is from Heather's Heavenly Vape - Adam's Apple. **GREAT juice**
provari mini setup.jpg
 

gwbard

Super Member
ECF Veteran
Verified Member
Aug 16, 2012
381
1,468
Florida
Been looking at a lot of awesome setups here. Kind of makes me hesitant to post mine, but I need post counts to post and ask question in different parts of the forum, so here we go. Just started vaping about 2 weeks ago and this is my very first setup. Provari mini with DCT Tank & 1.5ohm Carto. The juice (almost empty when I took the pic) is from Heather's Heavenly Vape - Adam's Apple. **GREAT Juice**
View attachment 215804
You're off to a great start! Excellent setup :D
 

MaDeuce

Super Member
ECF Veteran
Verified Member
Jan 30, 2013
984
2,943
Auburn, OH
Been looking at a lot of awesome setups here. Kind of makes me hesitant to post mine, but I need post counts to post and ask question in different parts of the forum, so here we go. Just started vaping about 2 weeks ago and this is my very first setup. Provari mini with DCT Tank & 1.5ohm Carto. The juice (almost empty when I took the pic) is from Heather's Heavenly Vape - Adam's Apple. **GREAT Juice**
View attachment 215804

Very nice first set-up.
 

Oryx

Full Member
May 13, 2013
37
20
Rowland Heights

Been vaping for eight months already.. Due to my addictive personality, it has been a big hole in my wallet but a good worthy hole nonetheless. Here are my current setups. Kicked Silver Bullet+Empire Drip Shield+Cisco Spec LR drip atty (on the right) and a Madvapes VV Gripper Mod + Vaporescence Liquinator Tank for the road (Left)

**Ok so I really don't know how to display my image like everyone else soooo... If anyone would be so kind, it'd be awesome if someone would PM me how to display the images.. #noob lol
 

Attachments

  • IMAG1929.jpg
    IMAG1929.jpg
    21.7 KB · Views: 94
Last edited:

Idaholandho

Gone Fishin'
ECF Veteran
Verified Member
Dec 8, 2012
7,379
23,171
Reading Naked
It's just 32AWG Kanthal ran side by side. A dual coil/single wick setup if you will. That build metered out at 1.3Ω. The wires are only crossed at the posts. Oxidize the mesh well :) Took me a couple tries, popped the coil on my first 2 tries before I remembered switching to a worn battery heh 3.5ish V.

Very nice. For that set up I def would oxy good although, I'm in a short lived no oxidizing trend and pulse oxidizing my fat wicks. I have found with all my builds in mesh, ekowool or silica that Torching the wire seems to "break" in the wire and I have almost no pops and the wire is far less springy and much easier to work.
 

bzmotoninja83

ECF Live Chat Moderator
ECF Veteran
Verified Member
Jul 2, 2012
2,161
2,796
42
Hopewell, Va
VAPE MAIL BRINGITH
sezydaqy.jpg


Also, got bored today. Got tired of knocking stuff over.... lol

tunenahe.jpg

utupuvys.jpg


The piece I used is usually for the bottom trim on a door frame. Next tile I'm going to get a little thicker wood and drill the tank holes a tad deeper so I can glue some 510 connections in to make the tanks secure too.
Sent from the 804
 
Status
Not open for further replies.

Users who are viewing this thread