Please explain how to adjust

[the ob]

I have a precise plus 18350 that I can't seem to get to work with many of the devices I am trying to attach.

Can someone let me know how to adjust the top 510 connection part to raise it so that we can use my devices.

I know this seems basic, but I can't figure it out.

 

[tybs_4045]

Sorry to tell you this but they are not adjustable. What are you screwing on it???? Maybe we can help you adjust that!

 

[forcedfuel50]

What tank/rba are you trying to run on it? Seems to be rash of no contacts lately. Just an FYI, Precise and PrecisePlus center post height hasn't changed in 3 years, but more an more manufacturers are coming out with connections that are about .015 too short (near as i can tell as they are basing getting their connector specs from atomizers, which are a bit too short for tanks) I can press out your post and press it back in .010 higher if you'd like, but keep in mind, atomizers won't sit flush with the top cap, they too will then be raised up again.

As an FYI, i'll be publishing as open source rba/tank/atomizer blueprints for manufacturers and modders alike wednesday with proper atomizer specs that will work on 99% of the mods out there, including the PrecisePlus, so hopefully we can get a little standardization in the industry.

 

[the ob]

Honestly, I have tried it with a number of them in the time I have owned it and have had a number of them not work.

It's a shame because it is a wonderful little device, but its hard to not be able to use it with everything.

So there is no way for me to adjust it on my own right?

 

[forcedfuel50]

Honestly, I have tried it with a number of them in the time I have owned it and have had a number of them not work.

It's a shame because it is a wonderful little device, but its hard to not be able to use it with everything.

So there is no way for me to adjust it on my own right?

Correct, it is pressed in and set up with a depth block, so it would need to be done by us. Unfortunately, some manufacturers are making their connections just a bit too short for the P+. The Pin on the P+ is set up so that atomizers are flush, but I can adjust it up .010 though if you'd like, send unit to, with 5.00 for return shipping:

Super T
Box 331
Sauk Rapids, MN 56379

 

[Killjoy1]

more manufacturers are coming out with connections that are about .015 too short

Yeah, that sounds about right. The only thing I've had a noticeable issue with is the Chinese DID copies, which screw flush to the cap and just barely make contact, close enough to work most of the time with occasional misfires in stock setup. Those are easily fixed by sticking a tiny o-ring or other non-conductive spacer under the head of the center pin of the atty.

As an FYI, i'll be publishing as open source rba/tank/atomizer blueprints for manufacturers and modders alike wednesday with proper atomizer specs that will work on 99% of the mods out there, including the PrecisePlus, so hopefully we can get a little standardization in the industry.

Good idea. Now we just need to make sure manufacturers actually read them . . .

 

[Riverboat]

. The Pin on the P+ is set up so that atomizers are flush.

Thats what Im talking about...... Set up for an atty like it should be.... I must be the last of the direct drippers.

 

[forcedfuel50]

Just a note that i have machined a new press block that sets up the PIN height .010 thousandths higher, which didn't adversly effect the look, but should now allow use with most rba/tanks that had too short of a PIN, can't guarantee it'll work with them all, but it should work with most now.

 

[snork]

Thats what Im talking about...... Set up for an atty like it should be.... I must be the last of the direct drippers.

Nuh-uh! There are still a bunch of us.

 

[snork]

Correct, it is pressed in and set up with a depth block, so it would need to be done by us. Unfortunately, some manufacturers are making their connections just a bit too short for the P+. The Pin on the P+ is set up so that atomizers are flush, but I can adjust it up .010 though if you'd like, send unit to, with 5.00 for return shipping:

Super T
Box 331
Sauk Rapids, MN 56379

You might be getting a little bagful of topcaps from me after the Holidays
I really don't have too much of an issue save for occasionally on my P+10s and 16340s. What I'm actually more worried about is the fact that on my Mark-T, for example, I have to sand its positive post once in awhile. I can see over the course of time that extra .010 on the bottom end might come into play.