Point me in the direction of.....

Status
Not open for further replies.

Vappers

Senior Member
ECF Veteran
Jan 23, 2014
243
159
United States
I believe that somewhere in this forum there is an explination of how to tell what ohms are safe for your battery... Im new to vaping and just bought my first mech mod, it does have a short protection chip that i put behind the batter.

If anyone would like to do some math:
Battery:
Kamery
ICR 18650
2000mAh 3.7V

What would be the lowest possible safe ohms for this battery? And how did you figure your math?

Thanks all!

My new toy :)
ZGtlile.jpg
 

State O' Flux

Vaping Master
ECF Veteran
Verified Member
Jul 17, 2013
4,844
4,993
Seattle
12 views, 2 hours and no help? Must be them manic Super Bowl preparations.
yes.gif


First of all, you calculate based on the batteries stated 'C' rating:

(C rating X (mAh ÷ 1000) = amps / example: C5 X (2000 ÷ 1000) = 10 amps)

Or, the stated "high-drain" maximum amp output (if so labeled) - which in some cases is indicated in both a short time span and a continuous load. If this information is not known, then you can deduce from the charge capacity an approximate, and logically conservative, safe rate.

Using the linked chart (produced by steam turbine based on information gathered from and collected by baditude and other sources) - the most common 2000mAh capacity battery (that isn't over-inflated by the mfg) is 10a.
As I don't recognize the battery label, and you've hidden any potentially useful label information from view ;) (When asking mech/RBA questions, please provide all pertinent information available to you - especially battery and resistance data), I must guess as to manufacture (these Chinese "kit batteries" are the cheapest of the cheap and frequently relabeled to hide their origins) - I'd think about calling it more a 7-8 amp rating. Safety first eh? :)

Now... we go to our ohms law calculator (one of hundreds found on the interweb... but I'm fond of this one), punch in our fully charged battery voltage, which should be very close to 4.2v or a bit less If you don't know this, then you don't have a DMM - If you don't have a DMM... you need one, and perhaps for convenience as well as safety, an ohm "build box".

So - 4.2v - 10a max continuous discharge - 0.42Ω is your absolute minimum resistance value - which if you review the chart for battery/resistance applications - lines up, as it should, on the conservative side. Until you become more battery and coil knowledgeable, stay conservative - stay safe.

As you are new to mech mods and rebuildables, I"ll also point you to a list of useful information - where the above, being very useful links, are repeated. I'd suggest starting with a single 1.0 ohm coil, and working your way down as you learn. If your atty is capable of dual coils, then two 2.0Ω coils (gross), for a 1.0Ω net resistance.

Cheers
 
Last edited:

Vappers

Senior Member
ECF Veteran
Jan 23, 2014
243
159
United States
Update: :)
Between State 0' Flux, Badditude and myself this has been solved! Thanks guys :)

The Math!
Using State 0' Flux's formula - C rating 1(found here) x (2000mAh / 1000 = 2) = 2 Amps Max Drain.

Then head here to our ohm calculator and input the voltage of the batt (3.7) and the max amps to find our lowest possible resistance.

TADA: 1.8 ohms :glare:

Off to ebay to find a better battery :oops:

Thanks for all the help guys!
 
Status
Not open for further replies.

Users who are viewing this thread