Argh just went into production this morning. (I don't actually care, but I'm Greek, I am required by law to complain about anything and everything.)
Printed DNA30 Bottom Feeder
- Thread starter gdeal
- Start date
- th_trl_thread_readers 0
- Status
Argh just went into production this morning. (I don't actually care, but I'm Greek, I am required by law to complain about anything and everything.)
I have two sets of the new internals on order, if you want we can swap.
Naaaah, I was just stirring trouble. Honestly, the only reason I really ordered the new internals was because I was ordering a steel fire button.
Mine went into production yesterday morning as well, with the 3.1.
No email from them though....
Out of curiosity do they always take a month, or is it because this is my first order ?
I ordered mine on 8/5 and got shipping notification on 8/11, this was my first order as well
A month? It only been available for less than two weeks... Some material/colors take longer in production, what did you get?
BTW, same offer stands that I put out to Kataphractos. I have the new version on order, glad to do a swap with you if you want.
@gdeal - Again, great thread priceless info.
Reading the thread through....again, I see someone previously asked about the display on the bottom. I am not sure this would be entirely healthy for me long term. Aside from caging it with titanium brings me to this question, in subsequent versions would it make sense to flip the the internals so that there may be room on top for the display?
I feel there may be I set it down in a condensation flood plain as in my bathroom counter top area where it is tough to see water on the slab?
I am just curious and hell bent on the Group Buy regardless, I suspect you have too thought of future placement. Thanks
Reading the thread through....again
, I see someone previously asked about the display on the bottom. I am not sure this would be entirely healthy for me long term. Aside from caging it with titanium brings me to this question, in subsequent versions would it make sense to flip the the internals so that there may be room on top for the display? I feel there may be I set it down in a condensation flood plain as in my bathroom counter top area where it is tough to see water on the slab?
I am just curious and hell bent on the Group Buy regardless, I suspect you have too thought of future placement. Thanks
Uh, the top comes off to fill the juice bottle and swap batteries. You'd need some kind of multi-pin connector to remote the display into the top, where there's really no room for it anyway.
The display itself is recessed quite a way in the bottom of the mod. I'll try to take a picture showing this in a bit.
Yep top comes off, seen it. Hence the reversal of the internals. The new Flask mod is what prompted the question.
Edit - I should of been more specific about flipping the internals, the bottom of the mod obviously would have to be the removable piece. I get the room issue, promise. I am just well....me and not so sure the bottom is the best answer for me. I am far too active to see this lasting but, I may surprise myself.
Last edited:
I should have said 21 days, my bad.
Nah... not worried at all, but appreciate the offer.
Just contemplating ordering a second set of parts, and I'm sure that won't be my last either
Edit
I've been watching this project for some time.
My sincerest gratitude goes to gdeal and the entire Beta Team for the tireless work on this, thank you.
Last edited:
OK, here you go:
I haven't tried setting it on a wet counter, but I doubt water could puddle deep enough on a flat surface (from which it could run off) to reach the display.
I have (unintentionally) dropped this mod onto a tile floor from my shirt pocket. The end with the display in it hit first. The impact was sufficient for the battery to flatten the lower battery contact. There was no other damage to the mod. The plastic it's made from seems to absorb impact pretty well.
I haven't tried setting it on a wet counter, but I doubt water could puddle deep enough on a flat surface (from which it could run off) to reach the display.
I have (unintentionally) dropped this mod onto a tile floor from my shirt pocket. The end with the display in it hit first. The impact was sufficient for the battery to flatten the lower battery contact. There was no other damage to the mod. The plastic it's made from seems to absorb impact pretty well.
No problem here Jake.... Ok I see what you have going on. You got polished bronze parts. They take up to 15 business days to make/ship.. so the Aug 27th date makes sense. It looks like they are just queuing up the black parts so that they finish up with the bronze parts. Shapeways is pretty good at meeting or beating ship dates in my experience.
Ok I see what you have going on. You got polished bronze parts. They take up to 15 business days to make/ship.. so the Aug 27th date makes sense. It looks like they are just queuing up the black parts so that they finish up with the bronze parts. Shapeways is pretty good at meeting or beating ship dates in my experience.@gdeal - Again, great thread priceless info.
Reading the thread through....again
I feel there may be I set it down in a condensation flood plain as in my bathroom counter top area where it is tough to see water on the slab?
I am just curious and hell bent on the Group Buy regardless, I suspect you have too thought of future placement. Thanks
I think the top would be more of a risk than the bottom....over squonking has been know to happen. The DNA screen is at least 4 mm off the base. Not sure what your flood plain looks like, but at least you now have a depth chart.
Thanks for the insight gdeal, that makes perfect sense.
Rossum gave me grief over the bronze until I told him it matched my favorite rose gold watch... then he just rolled his eyes as usual
Rossum gave me grief over the bronze until I told him it matched my favorite rose gold watch... then he just rolled his eyes as usual
That would make it "interesting" to get to the juice bottle.
That Flask Mod is pretty cool. But it's not a bottom-feeder.
That Flask Mod is pretty cool. But it's not a bottom-feeder.
Nor are the batteries replaceable in this version.
Was on my 'maybe' list until I finished watching Grimm's review.
Just ordered a second set of parts and played around with the options.
Any raw metal adds a couple days; polished anything adds ~2 weeks likely due to the labor involved.
This order has a raw brass spacer and estimated ship is 28 August.
Any raw metal adds a couple days; polished anything adds ~2 weeks likely due to the labor involved.
This order has a raw brass spacer and estimated ship is 28 August.
OK, here you go:
I haven't tried setting it on a wet counter, but I doubt water could puddle deep enough on a flat surface (from which it could run off) to reach the display.
I have (unintentionally) dropped this mod onto a tile floor from my shirt pocket. The end with the display in it hit first. The impact was sufficient for the battery to flatten the lower battery contact. There was no other damage to the mod. The plastic it's made from seems to absorb impact pretty well.
I have over squonkedI think the top would be more of a risk than the bottom....over squonking has been know to happen. The DNA screen is at least 4 mm off the base. Not sure what your flood plain looks like, but at least you now have a depth chart.
. Not to mention my Cyclone weeps out of the air hole. In fact, I think my Chalice II's are my only "dry" options.Yeah, I know. I clearly didn't think this through. I happened to be over loaded on testosterone without clarity thinking that I just invented world peace.That would make it "interesting" to get to the juice bottle.
That Flask Mod is pretty cool. But it's not a bottom-feeder.
I'm not even sure what I was f thinking
- Status
Similar threads
