Printed DNA30 Bottom Feeder

[Steamer861]

Just an FYI I'm using 2 FD adjustable BF'er 510's right now and this morning I woke up to check atomizer message If I remove the atty the message goes away.
As soon as I try to put it back on the dna locks and it give check atomizer message. I then have to remove atty and click 5 times to unlock
I want to get a few SS screws and mod this 510 So hopefully I can get it to work better

 

[TruckerMSA]

Just an FYI I'm using 2 FD adjustable BF'er 510's right now and this morning I woke up to check atomizer message If I remove the atty the message goes away.
As soon as I try to put it back on the dna locks and it give check atomizer message. I then have to remove atty and click 5 times to unlock
I want to get a few SS screws and mod this 510 So hopefully I can get it to work better

Are you using the SS needles?


Sent from the Truck O Shop

 

[Steamer861]

no just the brass pin

Are you using the SS needles?


Sent from the Truck O Shop

 

[TruckerMSA]

no just the brass pin

Hmmm, then somewhere your losing connectivity to the atty when screwed on. Are you using an o-ring inside the connector where the pin makes contact with atty?


Sent from the Truck O Shop

 

[Steamer861]

Yes I am It worked fine for a week or so I took it all apart and besides being a little wet all looks ok
I have the + lead soldered to the collar and I am suspecting this is were my problem lies
I will reconnect the
+ lead directly to the brass pin and see if it remedies the problem

Hmmm, then somewhere your losing connectivity to the atty when screwed on. Are you using an o-ring inside the connector where the pin makes contact with atty?


Sent from the Truck O Shop

 

[tiburonfirst]

a little off topic - anybody just looking for custom-made screws to work with fd's classic 510s take a look at a certain section of ecf

 

[Steamer861]

Thank You all ready got my 2 extras and I know exactly were there going

a little off topic - anybody just looking for custom-made screws to work with fd's classic 510s take a look at a certain section of ecf

 

[tiburonfirst]

lol, steamer! i was addressing people looking for just the screws

 

[TruckerMSA]

a little off topic - anybody just looking for custom-made screws to work with fd's classic 510s take a look at a certain section of ecf

What section would that be?


Sent from the Truck O Shop

 

[tiburonfirst]

co-op section

 

[TruckerMSA]

co-op section

Somehow I feel I should have known that.[emoji12]


Sent from the Truck O Shop

 

[rogue007]

I had to ask also..... First co-op here even though I've been here awhile. Get most of my stuff on the classifieds page or FB.

 

[Kataphraktos]

indeed, i am on the road. Or camping in a train station parking lot or sumpin'. So hit me with your best shot!

OMG run that blue car is on fire!

 

[tiburonfirst]

no such thing as a burning car in that particular country

 

[Rossum]

Yes... good idea. For bottom feed the spring adjust ability just isnt that important to me. I would rather have a static leak free seal.

Yep, about the only time I remove my BF atties (Cyclones) is on the mechs when I re-coil 'em (to check ohms) and then the same atty goes back on. On the DNA, there's no need to remove 'em even when recoiling, so the atty basically never comes off that one.

 

[Steamer861]

So I loaded my Shapeways cart with another whole unit. How long do you think I will have to wait for the 10% discount email? Does this work for sure?

 

[SeaNap]

Yep, about the only time I remove my BF atties (Cyclones) is on the mechs when I re-coil 'em (to check ohms) and then the same atty goes back on. On the DNA, there's no need to remove 'em even when recoiling, so the atty basically never comes off that one.

I soldered about a foot and a half of 18g wire onto the circuit board of my box ohm meter so I never have to take my attys off.

Sent from my iPad using Tapatalk

 

[Kataphraktos]

I soldered about a foot and a half of 18g wire onto the circuit board of my box ohm meter so I never have to take my attys off.

Sent from my iPad using Tapatalk

You know those beer hats, with the slots on either side for beer cans and tubes running down to the wearer's mouth area?

This is the vaping version of the beer hat.

Truly mesmerized and in awe.

 

[Rossum]

I soldered about a foot and a half of 18g wire onto the circuit board of my box ohm meter so I never have to take my attys off.

How much fudge factor do you add to your readings for the wire? Back of the envelope math says 3 feet of 18 gauge wire would be about 20 milli-ohms.

 

[tiburonfirst]

So I loaded my Shapeways cart with another whole unit. How long do you think I will have to wait for the 10% discount email? Does this work for sure?

all you can do is try