=/ Problems with my MVP 2.0

[Lethal-Dose]

Today I got 2 error messages on my MVP 2.0
One was the one in the picture and the other was 888.
When I put on my iclear30 on it, it read ohm0.0 and when I pressed the fire button it would stay green for like 15 sec.
And sometimes I got it to work right and it worked for like 15 min or so, but then it got messed up again.
Also time to time the ohms would even read form 0.4 to like 5.7 when I checked the ohm on the iclear30.

Any input? What should I do? I bought this from eBay, should I contact the seller?



vape On

 

[Vapoor eyes er]

Never had that prob on my MVP 2 but found this:
"I just stumbled upon this thread after having the same type of issues with a few iclear30. At first I thought like everybody that I wasn't making contact. My ohm reading on my MVP2 or VV3 were displaying "non" or "A 0.0". Pushed the pin out, re-screwed, cleaned the contacts etc...nothing worked.

I found the culprit, well in my case. Since it was always after a refilling, I decided to remove the rubber cap on top of the coils to look at them. The top coil seemed like it wasn't straight and might even touch the side of the chimney. I took a tweezer and re-centered the top coil. Replaced back the rubber cap. While screwing back top part with the drip tip, I noticed that if you screw it too tight, the rubber cap, coils and chimney start turning. My theory is that this moves the coils and the MVP 2.0 short protection prevent the tank from firing. So I just screwed it back snug but not tight and everything works perfect as before."

 

[EL Pistoffo]

If it doing it with other tanks that you know are good then yes, contact the seller. It's sounds like it's hosed to me. This thing isn't like pretty old or worn right? The MVP doesn't have a replaceable battery as far as I know. Once it's no good it gets tossed. It's a great mod, but a disposable one.

 

[Lethal-Dose]

Its about 2 months old. and yes it does this on all my iclear30s and my kanger pt 2

 

[Lethal-Dose]

I forgot to add all the iclear30s that give me the error work just great on my svd or my vamo.

 

[RubyRoo]

The error you are describing on your MVP means that you have a short on your iClear 30! You need to take off the tank, unscrew the top cap of the tank, and remove the silicone cap that rests on the coils and wicks. Inspect your coils and be sure that they are not touching any metal on the sides of the tube that the coils and wicks rest in. Take a needle, or a pin and fiddle with the coil a bit to work out any shorts. Hope this helps!

 

[TheKiwi]

Might not be entirely relevant, but I think there are some inconsistencies with the manufacturing of the connection heads on the mvp 2.

When my new one came, nearly every single one of my evods (ego threading) registered a short (0.0 led display), even if they showed 2.0 on my ohm meter. Used a ego-510 connection adaptor on my evods, and they worked fine on the mvp v2. Some things you wanna check:

1) make sure that whatever coils you're using arent shorting out to begin with. Check it with a ohm meter if you have one. If not, visual inspection to make sure the coils aren't wriggling around and touching the sides or each other.

2) check to make sure the rubber/silicon insulators aren't burnt through. Also make sure that if you're recoiling yourself, excess coils are cut off as much as possible.

3) wriggle your tanks around when it's on the mvp, and keep checking the ohms. If it changes from a short to a proper ohm reading and back and forth while you're wriggling it, well, you have a bad connection.

Good luck with your new mvp tho. I absolutely love it and even if the battery croaks, I'm just gonna leave it at my desk as a pure pass through vape. that or as a plugged in ohm meter if my current one dies.


Sent from my iPad using Tapatalk

 

[Caridwen]

The error you are describing on your MVP means that you have a short on your iClear 30! You need to take off the tank, unscrew the top cap of the tank, and remove the silicone cap that rests on the coils and wicks. Inspect your coils and be sure that they are not touching any metal on the sides of the tube that the coils and wicks rest in. Take a needle, or a pin and fiddle with the coil a bit to work out any shorts. Hope this helps!

That's what it sounds like to me too. Awhile ago we had a rash of smokemizer clearos shorting out batteries.

You can buy a cheap multimeter for about $6 to double check.

 

[Caridwen]

Might not be entirely relevant, but I think there are some inconsistencies with the manufacturing of the connection heads on the mvp 2.

When my new one came, nearly every single one of my evods (ego threading) registered a short (0.0 led display), even if they showed 2.0 on my ohm meter. Used a ego-510 connection adaptor on my evods, and they worked fine on the mvp v2. Some things you wanna check:

1) make sure that whatever coils you're using arent shorting out to begin with. Check it with a ohm meter if you have one. If not, visual inspection to make sure the coils aren't wriggling around and touching the sides or each other.

2) check to make sure the rubber/silicon insulators aren't burnt through. Also make sure that if you're recoiling yourself, excess coils are cut off as much as possible.

3) wriggle your tanks around when it's on the mvp, and keep checking the ohms. If it changes from a short to a proper ohm reading and back and forth while you're wriggling it, well, you have a bad connection.

Good luck with your new mvp tho. I absolutely love it and even if the battery croaks, I'm just gonna leave it at my desk as a pure pass through vape. that or as a plugged in ohm meter if my current one dies.


Sent from my iPad using Tapatalk

Good suggestions!

 

[Lethal-Dose]

Thanks for suggestions. But im just gonna order a new one from 101vape.

Might not be entirely relevant, but I think there are some inconsistencies with the manufacturing of the connection heads on the mvp 2.

When my new one came, nearly every single one of my evods (ego threading) registered a short (0.0 led display), even if they showed 2.0 on my ohm meter. Used a ego-510 connection adaptor on my evods, and they worked fine on the mvp v2. Some things you wanna check:

1) make sure that whatever coils you're using arent shorting out to begin with. Check it with a ohm meter if you have one. If not, visual inspection to make sure the coils aren't wriggling around and touching the sides or each other.

2) check to make sure the rubber/silicon insulators aren't burnt through. Also make sure that if you're recoiling yourself, excess coils are cut off as much as possible.

3) wriggle your tanks around when it's on the mvp, and keep checking the ohms. If it changes from a short to a proper ohm reading and back and forth while you're wriggling it, well, you have a bad connection.

Good luck with your new mvp tho. I absolutely love it and even if the battery croaks, I'm just gonna leave it at my desk as a pure pass through vape. that or as a plugged in ohm meter if my current one dies.


Sent from my iPad using Tapatalk

 

[TheKiwi]

Thanks for suggestions. But im just gonna order a new one from 101vape.

Good luck! Mine was from 101vape too and it had a wonky ego connection.


Sent from my iPhone using Tapatalk

 

[rith]

Today I got 2 error messages on my MVP 2.0
One was the one in the picture and the other was 888.
When I put on my iclear30 on it, it read ohm0.0 and when I pressed the fire button it would stay green for like 15 sec.
And sometimes I got it to work right and it worked for like 15 min or so, but then it got messed up again.
Also time to time the ohms would even read form 0.4 to like 5.7 when I checked the ohm on the iclear30.

Any input? What should I do? I bought this from eBay, should I contact the seller?

View attachment 287055

Vape On

I so glad you have this issue because I have the same issue too and stupid ... 101vape shipped me the same stuff with the same problem so bs


Sent from my iPhone using Tapatalk

 

[rith]

got this From 101vape and they take 2 weeks I exchange to replace it. But guess what I got the Same one back with the same problem they won't even exchange even after pictures and talking to customer service f them


Sent from my iPhone using Tapatalk

 

[rith]

got this From 101vape and they take 2 weeks I exchange to replace it. But guess what I got the Same one back with the same problem they won't even exchange even after pictures and talking to customer service f them


Sent from my iPhone using Tapatalk

Sent from my iPhone using Tapatalk

 

[Lethal-Dose]

So 101vapes is not the best place to order them?

 

[rith]

So 101vapes is not the best place to order them?

Not when it comes to quality and return policies im speaking in exp. and what I had web thru with my mvp2. They gave me the same one back, how would you feel? It took them 2 weeks to ship me out the product I sent them that is obscured.


Sent from my iPhone using Tapatalk

 

[rith]

Ok I need to know what you have on your MVP 2 setup. I just use a 510 to 510 adapter on my hh357 atomizer and it works good. But idk for how long yet. It's on been an hour use so far and no crazy code yet


Sent from my iPhone using Tapatalk