RDA Questions

[BigCap]

Hey guys, I have a couple newbie questions here. Hope somebody can help me out here.

So I just purchased my first RDA, just a cheap omega clone, and it came pre wicked with dual coils.

I checked the ohms on my itaste vv 3.0 .. First it read 1.4 , then I tightened the screws a little, it went to 1.3 to 1.0, tightened all the way, and it went to 0.7 and then I unscrewed it a bit, and it read 5.7, then 5.4. Screwed them back down tightly again and it's reading 0.7 steadily, after about 10 straight clicks.

I plan on vaping this with an nzonic v5 clone & Sony vtc4 battery 2100 mah

1. Am I suppose to wash this rda out before using?

2. Is it safe to use the pre made wicks that come with it? Or should I burn the coils with a lighter or dry burn before using?

3. Would the ohms jumping around like they did when I was playing with the screws be a problem? It never measured under .7 and the itaste has always been fairly accurate on the ohms.

I have terrible anxiety when it comes to this stuff. Thanks so much in advance for any help.


Sent from my

 

[porkchopbun]

Please wash it first with a Dawn bath, and read this...

http://www.e-cigarette-forum.com/forum/blogs/baditude/4454-7-information-resources-your-first-rba.html

 

[valooper]

Honestly bigcap I never use pre made coils or wicks because they make me uneasy and want to choke a poodle!!

I would grab some kanthal and cotton and build your own coils 28ga with 10 wraps around a 5/64 drill bit should foot the bill nicely

 

[BigCap]

Please wash it first with a Dawn bath, and read this...

http://www.e-cigarette-forum.com/forum/blogs/baditude/4454-7-information-resources-your-first-rba.html

Ok thanks, I don't understand the meaning behind the link though..


Sent from my

 

[Nytebreed]

Throw those coils away.

All of the coils that I have ever seen that came in clone attys were complete unsafe junk, one my friend got, who was smart enough to have me rebuild before he used, was a dead short when I tested it.
I don't want to see what would have happened if his 26650 went into thermal runaway.

 

[valooper]

Watcha mean what dont you understand?

 

[valooper]

Ok thanks, I don't understand the meaning behind the link though..


Sent from my

Whatcha mean?

 

[porkchopbun]

Ok thanks, I don't understand the meaning behind the link though..


Sent from my

that link is beginners guide for RBA, coils, ohm's, it's a good read, it's your choice, but the Nzonic is mechanical mod. There is no protection if something is faulty. If you're already experience in using a mechanical /RDA, then skip it.

 

[BigCap]

Honestly bigcap I never use pre made coils or wicks because they make me uneasy and want to choke a poodle!!

I would grab some kanthal and cotton and build your own coils 28ga with 10 wraps around a 5/64 drill bit should foot the bill nicely

Haha ok thanks, I did buy some organic cotton squares, and I have some kanthal in 30g and the holes are 3mm pre drilled. I just was wondering since I have never built a coil, I plan to tonight, but I am just wanting to dive right in now. [emoji3]


Sent from my

 

[BigCap]

that link is beginners guide for RBA, coils, ohm's, it's a good read, it's your choice, but the Nzonic is mechanical mod. There is no protection if something is faulty. If you're already experience in using a mechanical /RDA, then skip it.

The link shows something regarding pictures?


Sent from my

 

[BigCap]

that link is beginners guide for RBA, coils, ohm's, it's a good read, it's your choice, but the Nzonic is mechanical mod. There is no protection if something is faulty. If you're already experience in using a mechanical /RDA, then skip it.

I just bought the mech because I want to get into lower ohms, so I am not pulling every muscle in my throat to get a nice pull..thanks again


Sent from my

 

[valooper]

Oh heck yeah man I gotcha lol tjis is gunna make me sound like a hypocrite but when I got my new mini rda i tested the resistance and checked for shorts put like 4 drops on it and took the worlds quickest pull I kust had to try it lol

 

[BigCap]

Throw those coils away.

All of the coils that I have ever seen that came in clone attys were complete unsafe junk, one my friend got, who was smart enough to have me rebuild before he used, was a dead short when I tested it.
I don't want to see what would have happened if his 26650 went into thermal runaway.

Thanks yeah, plus it being a clone from china came in an all black box with no company name, probably would be best to chuck em..thank you


Sent from my

 

[valooper]

I just bought the mech because I want to get into lower ohms, so I am not pulling every muscle in my throat to get a nice pull..thanks again


Sent from my

Get ready to suck in and have your lungs fall out of your back end iif you want to try cloud chasing lol

 

[BigCap]

Lol I ain't trying to get into super sub ohms, under .5 but yeah definitely need get more vape!


Sent from my

 

[valooper]

You should definitely post pics once you get that bad girl built!!

 

[BigCap]

Oh heck yeah man I gotcha lol tjis is gunna make me sound like a hypocrite but when I got my new mini rda i tested the resistance and checked for shorts put like 4 drops on it and took the worlds quickest pull I kust had to try it lol

That is Exactly how I plan to do it! Lol


Sent from my

 

[BigCap]

You should definitely post pics once you get that bad girl built!!

Will do, yup I am going to just build on it tonight. Ill post the pics here when finished [emoji106]


Sent from my

 

[USMCotaku]

Lol I ain't trying to get into super sub ohms, under .5 but yeah definitely need get more vape!


Sent from my

cautionary note....what strength of nicotine are you currently using? Anything over 3-5mg on your first RDA, not advisable. Don't think that because you were vaping 21mg in your tank you can handle it dripping

 

[Susan~S]

Ok thanks, I don't understand the meaning behind the link though..Sent from my

It's obvious to everyone that you are very inexperienced based on your questions. It would serve you well to read all the links posted in that thread so that you know what you are doing.