I'm having issues with my devices. Please let me explain: Devices, VV3, istick x2 both with modded plastic top caps and FDV V4 510's, and an ipv mini. Using a Erl mini clone like this one.
Tests done this morning
BigDripper 1.4 single coil pre-wrapped coils from FTVV White - 1.6 - 1.7
VV Black - 1.5 - 1.6
iStick Black with FDV V4 - 1.5
iStick Silver with FDV V4 - 1.5
iPV - 1.3 - 1.4 (tried dual 1.4 coils for a calculated 0.7 ohm [read low <0.5 would not fire])
Kanger factory 1.3
VV White - 1.3 - 1.4
VV Black - 1.3
iStick Black with FDV V4 - 1.3
iStick Silver with FDV V4 - 1.3
iPV - 1.2 reading low
R91 hand wound calculated to 1.8 with Steam engine
VV White - 1.8
VV Black - 1.8
iStick Black with FDV V4 - 1.8
iStick Silver with FDV V4 - 1.8
iPV - 1.7 reads low
Erlkonigin; Erl coil is wrapped on a 2.4mm with 30 guage K-A1 to 1.6 ohm according to Steam Engine. Using my sausage fingers and a multi-meter the coil is right around 1.5 - 1.8 ohm (I assume the variance is due to sliding the leads on the legs).
VV White - NON (Erl 510 is to short)
VV Black - NON (Erl 510 is to short)
iStick Black with FDV V4-
iStick Silver with FDV V4 - 2.1 (Why so high?)
iPV - 1.7
Can't figure out why trying dual coils on the BD I had readings to low to fire on the iPV, and now why the iStick is reading so high with the Erl clone. I'm at a loss.
Tests done this morning
BigDripper 1.4 single coil pre-wrapped coils from FTVV White - 1.6 - 1.7
VV Black - 1.5 - 1.6
iStick Black with FDV V4 - 1.5
iStick Silver with FDV V4 - 1.5
iPV - 1.3 - 1.4 (tried dual 1.4 coils for a calculated 0.7 ohm [read low <0.5 would not fire])
Kanger factory 1.3
VV White - 1.3 - 1.4
VV Black - 1.3
iStick Black with FDV V4 - 1.3
iStick Silver with FDV V4 - 1.3
iPV - 1.2 reading low
R91 hand wound calculated to 1.8 with Steam engine
VV White - 1.8
VV Black - 1.8
iStick Black with FDV V4 - 1.8
iStick Silver with FDV V4 - 1.8
iPV - 1.7 reads low
Erlkonigin; Erl coil is wrapped on a 2.4mm with 30 guage K-A1 to 1.6 ohm according to Steam Engine. Using my sausage fingers and a multi-meter the coil is right around 1.5 - 1.8 ohm (I assume the variance is due to sliding the leads on the legs).
VV White - NON (Erl 510 is to short)
VV Black - NON (Erl 510 is to short)
iStick Black with FDV V4-
iStick Silver with FDV V4 - 2.1 (Why so high?)
iPV - 1.7
Can't figure out why trying dual coils on the BD I had readings to low to fire on the iPV, and now why the iStick is reading so high with the Erl clone. I'm at a loss.
