So I saw the reuleaux today and it looks really nice. I am currently running a snow wolf with a kennedy. Is it worth getting one or should I just stick with the wolf?
Reuleaux RX200 vs Snow wolf 200w 1.5
- Thread starter Shipdawg800
- Start date
- th_trl_thread_readers 0
- Status
Not many in the hands of user's so hard to answer at this point all comes down to the chip, on face value the rx200 was good enough for me to take a punt on a preorder for £32 if it turns out to be rubbish I'm sure I can get another chip in there.
I hear joyetech makes the Reuleaux board and while made in China, the company behind the mod is American. I'm looki ng into the Reuleaux dna 200 however I would probably take the Reuleaux RX200 over the Snow Wolf after the accuracy tests I've seen and positive reception in my Facebook groups.
Sent from my 831C using Tapatalk
Sent from my 831C using Tapatalk
Where do you learn about the different chips? I've been searching all over the forums and the Internet for that matter and I can't really find anything
Normally I would recommend avoiding any brand new chipset until it's been well tested by the community.
However, with 200W, three 18650 batteries, temperature control with support for Ti, Ni, and SS wire, and a $60 price tag it's hard not to say go for it. Even if it turns out to be a turd you won't loose much money, and if it's everything the manufacturer claims then it's probably the best buy on the market right now.
However, with 200W, three 18650 batteries, temperature control with support for Ti, Ni, and SS wire, and a $60 price tag it's hard not to say go for it. Even if it turns out to be a turd you won't loose much money, and if it's everything the manufacturer claims then it's probably the best buy on the market right now.
Just Google the chip name or failing that "rx200 chip" and you'll soon find what you want.
Just picked up the DNA 200 version today and really like it.
Sent from my 831C using Tapatalk
Sent from my 831C using Tapatalk
Well just to satisfy my curiosity I set my xcube 2 to 220°C and fired it for the full ten seconds (tc has worked great for me on xcube 2) and cotton burned not completely through like it did in the German review video but not far off and confirms for me that this isn't a major issue for me as I normally vape at 180° C. Add in the firmware upgrading and any tc issues will be sorted out, for the money and the battery life it really is a no brainer getting the rx200 just don't buy from a UK vape site as they are advertising them in the £65 range lol.
But is it worth getting one when I already have a snow wolf?
Sent from my SM-G928T using Tapatalk
Only you can answer that to be honest I'm stocking up on mods ready for the legislation coming in next year and will be buying two more mods in December one being the yihi sx mini ml class and planning on getting the reuleaux dna200 so given the low price on the rx200 it was a no brainer. This cheap mod will give me a chance to see how I get on with the reuleaux before spending a lot more money on the dna200 version.
The Reuleaux DNA 200 is also very well built and very comfortable to hold unless you have little hands. Just like the SX Mini, it's made out of Zinc Alloy. The 510 threading is also Stainless Steel. I bought one yesterday and love it.
Sent from my 831C using Tapatalk
Sent from my 831C using Tapatalk
This thread is about the rx200 not the dna200 which by the way is not a limited run it's production is being limited by evolv's inability to supply sufficient complete boards to meet demand as soon as evolv resolve this the wismec dna200 production will increase there is no need for anyone to rush buying anything.
Not according to this vendor. I'm just going by what I read.
Sent from my 831C using Tapatalk
Yes I saw that at ecigone and it is not correct and I can walk to a b&m in my town tomorrow and get the dna200 version they are in short supply but it is all down to a shortage of screens to attach to the dna200 boards, screens are in very high demand at the minute and other items are suffering. Wismec is onto a complete winner with the dna200 version and they are only lowering production because of the evolv issues and once those are resolved the production of the dna200 version will increase. Although the rx200 was planned it was never intended to replace the dna version more to have products at different points in the market though I suppose if shortages go on for any length of time and the RX version proves popular they may rethink but at this moment in time the plan is to have both versions available for customer's to choose.
That's good if it's not correct. I was just relaying the message I read since you showed interest. I absolutely love this mod and if the RX200 is anything like it, I'll definitely buy one to use as a work beater.
Sent from my 831C using Tapatalk
Sent from my 831C using Tapatalk
I think ecigone have just misinterpreted or maybe their original enquiry wasn't answered properly likely due to poor English anyone that's dealt with Chinese company's has hit the problem often lol, but yeah it's an evolv issue which will hopefully be resolved quickly. I've bought an rx200 mainly to make sure the form factor suits me as I'm planning on getting the dna version but I can check the physical side of it now without spending the larger amount.
I'll just say the form factor is great. Most comfortable mod I've held next to the SX Mini. Not sure about the RX200 but the DNA200 is also made out of Zinc Alloy just like the SX. It is big though meaning I wouldn't recommend it to a somebody with little hands.
Sent from my 831C using Tapatalk
Sent from my 831C using Tapatalk
Yeah shape of it is well designed should fit well in hand, but mines coming from fasttech so couple of weeks away yet.
- Status
Similar threads
- Locked
