Silver Bullet, eGo-T, and 510 to 510 Adapter?

[ManicMaurice]

My brother-in-law just quit smoking and started vaping. He picked up a mall kit and has been extremely unhappy with its performance (go figure, I warned him). I want to support him, so I'm going to send him a new kit. I want to send him a Silver Bullet, AW 2900 mAh 18650s, 510 to 510 adapters, and eGo-T attys/tanks.

My question is, has anyone tried the new eGo-T attys/tanks on an Omega or a Silver Bullet?

This is the adapter that I'm looking at ...

Heaven Gifts > eGo charging adapter

Sorry about the non AltSmoke link. I don't think AltSmoke carries this adapter, so I will have to pick it up somewhere else.

 

[Jimi Mack]

This adapter will not work on a SB. A SB has a removable battery that HAS to be removed to be charged to need to then order a battery charger with your SB and batteries.

 

[Wench]

I think Jimi didn't understand what your trying to do.

I have the same 510 to 510 charger adapter ( it's basically just a adapter)and use it on my ego to get some length to it so I can use a 306 with the cone.
I don't have a SB but I have the Omega so it's the same 510 connector.
The 510 to 510 works just fine on it.
It should work with the Ego-T to help extend it up and give it the clearance it needs (the Mega Ego Atty's are the same, need clearance).
You can also use 510 to 901 and then a 901 to 510 adapters together to give it the space it needs.

 

[ManicMaurice]

This adapter will not work on a SB. A SB has a removable battery that HAS to be removed to be charged to need to then order a battery charger with your SB and batteries.

I'm just going to use the 510 to 510 adapter to get a little extra clearance on the connector, so it can be used with eGo-T attys and tanks. Thanks all the same Jimi.

The 510 to 510 works just fine on it.
It should work with the Ego-T to help extend it up and give it the clearance it needs (the Mega Ego Atty's are the same, need clearance).

Thanks Wench. I figured it would work, but didn't want to order anything until I was sure.

 

[Jimi Mack]

Sorry, my FUBAR.... I thought you were trying to get it to charge through that adapter.

 

[ManicMaurice]

Sorry, my FUBAR.... I thought you were trying to get it to charge through that adapter.

No worries.

 

[Quick1]

This adapter will not work on a SB. A SB has a removable battery that HAS to be removed to be charged to need to then order a battery charger with your SB and batteries.

Ummm, I don't see why not. It might take a lot longer to charge but it would work... I'd make sure to use protected batteries (protected from over charge in case the charging adapter doesn't have a proper cutoff). Probably not the best idea considering the price of a proper charger for the big batteries.

 

[LukeNM]

That battery charger extension is longer that what is needed. Someone needs to make 510 to 510 adapter specifically designed for a tube mod to a eGo-T atomizer. I started emailing some tube mod vendors to see if they plan to machine something like this.

 

[ManicMaurice]

That battery charger extension is longer that what is needed. Someone needs to make 510 to 510 adapter specifically designed for a tube mod to a eGo-T atomizer. I started emailing some tube mod vendors to see if they plan to machine something like this.

It's a little long, but it works perfectly.

 

[Robert T]

I use stacked adapters to make the eGo-T work with my SB but they're still a little to long for the atty to sit flush with the top. Somewhere I saw some adapters that claimed to be the thinest around, I think they called them "stealth adapters" Does anyone know where to get these? I just can't remember where I saw them.

 

[Sacker]

im waiting to get these in to test it out 510 modders connector I like the low profile vs 510 to 510 charging adapters. Ill test it out when it comes, I have an bsb/ego t's

 

[Sgt. Pepper]

Those 510-510 adaptors from avidvapor and 1/4 inch. I have 2 of them and I'm planning on stacking them on my Provari to use with the eGo-T. It's going to be close, but it's all hypotheical until I get the provari.

Hope this helps.

cheers,

 

[Robert T]

im waiting to get these in to test it out 510 modders connector I like the low profile vs 510 to 510 charging adapters. Ill test it out when it comes, I have an bsb/ego t's

This might just work! Thanks alot!

 

[Robert T]

im waiting to get these in to test it out 510 modders connector I like the low profile vs 510 to 510 charging adapters. Ill test it out when it comes, I have an bsb/ego t's

I found the "stealth adapter" again after I looked at the 510 modders connector. It looks like with the stealth adapter and a 901 to 510 adapter stacked it will be real close. I'll let you know. Please let us know if one modders connector will work.

 

[Sacker]

Those 510-510 adaptors from avidvapor and 1/4 inch. I have 2 of them and I'm planning on stacking them on my Provari to use with the eGo-T. It's going to be close, but it's all hypotheical until I get the provari.

Hope this helps.

cheers,

My thoughts exactly, I ordered 2 of them and a 510 to 510 maybe Monday if I'm lucky, some folks have already cut the Ts to the length of where the connector reaches, I like the idea, but it will be not so good if you stick it back to the original battery.

 

[Sacker]

generic visuals with 2 of them without the included washers... looks great :



with one + washer = no go

other stuffs didnt come in so can't see the height difference from a stock 510 to 510 coupler...

(though 1 with washer or without washer works fine with the Provari the draw is stiff, works better with 2)

 

[Robert T]

That's what mine looks like with regular adapters stacked(510 to 901-901 to 510) The stealth adapter will bring it down quite a bit I hope.

 

[Sacker]

the stealth adapter rim is half size of the 510 washer (height wise), so just barely smaller. too technical for me, to notice that much tbh.

 

[jasezero]

How is the eGo-T atty at 3.7v? My friend has it, uses it on a boxmod and didnt like it...thinks it was too harsh. I have the SB and was considering the tank atty but am worried about burning juice taste.

 

[ManicMaurice]

How is the eGo-T atty at 3.7v? My friend has it, uses it on a boxmod and didnt like it...thinks it was too harsh. I have the SB and was considering the tank atty but am worried about burning juice taste.

I didn't really care for the eGo-T at 3.7v, so I picked up a couple AW LiFePO4 batteries and I'm happy with the combo.