SmokTech The Natural - New mechanical device

[Fullknight]

The way mine works i take off the 18350 tube and an 18500 works,but 18490 probably better.
I leave all tubes together and put a kick in with 18500mah flattop ,works great,probably better with 18490.
I got mine from ExhaleVapors received yesterday.


Sent from my iPhone using Tapatalk

 

[jeffsm3]

Yea. Muzic I just noticed that. Full knight thanks for the info. Still think I may go with the ccts instead.

 

[WinchellNomNom]

I like my chichi, but its ugly. I dont take it out. Unless someone is in need of a telescopic vibrator, without the vibration.
Excelent mod for the 27 i spent on it.
Sent from my SCH-I605 using Tapatalk 2

 

[fogmachineroy]

I noticed on Rawr's website it calls for AW IMR batts, is there a difference in size between AW IMR batts and non AW IMR batts?

 

[Fury83]

I noticed on Rawr's website it calls for AW IMR batts, is there a difference in size between AW IMR batts and non AW IMR batts?

There is a size difference between a lot of types of batteries. Brands, mah, button or flat, protected or no...all a bit different. e-fest rebrands so e-fests could be different from each other.

Sometimes it matters and sometimes it doesn't. They probably call for AW IMR's because they are known to be good batteries and it's the only brand rawr sells.

 

[USinchains]

My unprotected AW IMR 18650 1600mAh are almost 5mm shorter than my protected Ultrafire 18650 2400mAh batts.

 

[congaman]

If someone finds a 18490 or 18500 that fits the natch with no gaps please post. Gotvapes efest 18500 button top does NOT fit without a gap. Wish they had stated that before i ordered 2 of them and they will not accept returns! Just want to make sure of the fit before i dive in for some more batteries (AW preferably)!

 

[anavidfan]

Im expecting my Natural today. I wanted to make what the consensus on the batteries that work on the Natural with and without the kick. I have the following batteries: AW IMR 18650, 18500 and 18350. I want to be sure I have everything ready, charged and my atomizer set up with a lower ohm wick for it with out the Kick also.

Thanks everyone

BTW, all are button tops except for the 18500 IMR Efest.

 

[VapingTurtle]

If someone finds a 18490 or 18500 that fits the natch with no gaps please post. ...

The Natural in my hand right now has the 18500 tube, the switch section, the top cap and the bottom cap; AW 18490 IMR (1100mAh); no gaps.

 

[anavidfan]

Just got it in the mail, nice PV, well finished. The adjustable pin is simple to use. Only thing left for me to do is finish this tank of juice in my Ody and to make a lower res coil. Its a 2.7 ohm coil right now, its vaping fine, but I know it can be better. Very pleased with it so far. Liking it in the small stealth size. Have to get used to palming the button.

 

[WinchellNomNom]

Just got it in the mail, nice PV, well finished. The adjustable pin is simple to use. Only thing left for me to do is finish this tank of juice in my Ody and to make a lower res coil. Its a 2.7 ohm coil right now, its vaping fine, but I know it can be better. Very pleased with it so far. Liking it in the small stealth size. Have to get used to palming the button.

Picture with ody pls!

Sent from my SCH-I605 using Tapatalk 2

 

[jamesfarrell]

Yeah this is complete BS.

Pics or it didn't happen. That goes for all ya alls. lol

 

[jamesfarrell]

Can someone please answer me this? With tank atomizers they don't fit flush? Do you file the top a bit, then the pin, I think I read. That's the screw like thing a few posts ago? The brass piece? I'm assuming you can remove it?

 

[VapingTurtle]

If anyone figures out a way to soften the action on the button spring, please post it!!

 

[WinchellNomNom]

Can someone please answer me this? With tank atomizers they don't fit flush? Do you file the top a bit, then the pin, I think I read. That's the screw like thing a few posts ago? The brass piece? I'm assuming you can remove it?

Yes it screws out. You file down the side that touches the atty. And to get it perfectly flush you have to file down the top of the 510 connector.

Sent from my SCH-I605 using Tapatalk 2

 

[WinchellNomNom]

If anyone figures out a way to soften the action on the button spring, please post it!!

Keep using it and it loosens up nicely.

Sent from my SCH-I605 using Tapatalk 2

 

[anavidfan]

I will definitely post a pict of it. Im charging up some batteries and trying my best to finish this tank of Cuban cigar juice. I need a lower res coil. This 2.7 ohm is not performing well enough with the 3.7 volt combo.
Oh the sacrifices I do to please you guys.

 

[jamesfarrell]

So there's two sides. The side that touches the battery and the other side that the tank/ atty / cart plugs into. I'm sorry, I'm an idiot. Unless I see exact pictures I can't understand. To me, it seems like whatever you attach to this thing, it does not fit flush. So, my guess would be you have to grind down the part that the tank/atty/cart screws into right? or do you grind down the whole top cap, stainless steel part?
Wish I had the ... thing in my hand already and my questions would be answered.

My new signature is going to be "I walked out of gotvapes with my pants down around my ankles"

What a fool. $80 each x 2. Could have got 3 of them if I had some patience to do some research. Oh well.

 

[anavidfan]

Hello, here is the photo I promised. This my Odysseus RA tank. I adjusted the pin on the connection and sanded down the 510 flush to the top of the PV. I think I over adjusted the pin because there is a slight gap on the mid section which was not there before I adjusted it. I was in a hurry to get a pict up. So I will take care of the pesky gap when I clean the coils and dry burn.

 

[WinchellNomNom]

Hello, here is the photo I promised. This my Odysseus RA tank. I adjusted the pin on the connection and sanded down the 510 flush to the top of the PV. I think I over adjusted the pin because there is a slight gap on the mid section which was not there before I adjusted it. I was in a hurry to get a pict up. So I will take care of the pesky gap when I clean the coils and dry burn.

Looks pretty. Nice choice of tank finish. Contrast is excellent.

Thanx!

Sent from my SCH-I605 using Tapatalk 2