Snow Wolf not detecting Ti? Help please!

[Five Clicks]

Hi all, I recently went into temp control and was ecstatic when managed to get some Grade 1 Titanium. However, after building and screwing on the tank to my new V1.5 Snow Wolf (SW), it doesn't stay in temp control mode. "Power" takes over the temp display as though I had put on a kanthal build after firing for a while. I've googled to no avail and tried rebuilding the deck but - no results.

Here is the setup if it helps:
tank: Billow V2
Pure "Best Choice" 28ga Titanium wire, Spaced dual coil, 9 wraps each, 2.5mm in diametre.
~0.68 ohms.

I understand there might be flaws in the build (not pertaining to my problem) but I hope we can leave them for another discussion.

I'm trying to avoid nickel at the moment, I know the SW doesn't support Ti but it should at least detect it right? Let me know if I missed out anything or if I can provide more info.

Thanks!

 

[cloudysheep]

I know the SW doesn't support Ti but it should at least detect it right?

Thanks!

this........





what means???

 

[Robert Cromwell]

A .68 build is a bit high for it to detect it as TC?
I dunno?

 

[Five Clicks]

this........





what means???

Oh, pai seh for not being clear. By "doesn't support Titanium" I meant that the way the Snow Wolf interprets ohms to get a temperature reading is configured to Nickel and not Titanium. Thus, you do not get the actual temperature you set when a Titanuim build is put on. I read that Ti is around 60 deg C or 140 deg F warmer. I meant to ask if I have to manually switch it to temp control since it doesn't automatically.

I have noticed Snow Wolves staying in temp control mode with a Titanuim build. (skip to around 3min 04sec).

A .68 build is a bit high for it to detect it as TC?
I dunno?

Thanks! I'll start looking in that direction. Not sure if there is a "max ohm" limit for TC.

 

[xKaijux]

I dont think snow wolf detect Ti...

 

[Five Clicks]

I dont think snow wolf detect Ti...

Is it possible to stay on ('coz when you first screw in a "new atomizer" it is in TC mode"), or switch to temp control then? I've read that you have to compensate and adjust the temperature when using Ti so I'm under the assumption you can use TC on Ti on the SW.

 

[xKaijux]

It is possible actually. Whats your built? And the size of the Ti? And also the set up you're trying on right now, maybe I or some other members here can help you out!

 

[Five Clicks]

It is possible actually. Whats your built? And the size of the Ti? And also the set up you're trying on right now, maybe I or some other members here can help you out!

haha, possible how? The build is in my original post, let me paste it here for you. Thanks!

Here is the setup if it helps:
tank: Billow V2
Pure "Best Choice" 28ga Titanium wire, Spaced dual coil, 9 wraps each, 2.5mm in diametre.
~0.68 ohms.

I understand there might be flaws in the build (not pertaining to my problem) but I hope we can leave them for another discussion.

 

[CAPSNOSPACE]

go checkout the post on ti coils by craftvApery


Sent from my iPhone using Tapatalk

 

[Five Clicks]

go checkout the post on ti coils by craftvApery


Sent from my iPhone using Tapatalk

Hi! Are you refering to this page? I went through it last week, it gave great insight into Ti safety and building. Didn't find a solution to my Snow Wolf problem, unless I missed out something..

Thanks!

 

[charles8888]

My sigelei dont support ti too. I jus switch to joules mode n use it 300f. So far so good.