someone please tell me what the problem is

[jamie0516]

I have an aerotank on my MVP and it will not pull! My MVP shows the word non on the screen. I will get it working for a few puffs but even then I'm having to pull hard to get anything. I've changed coils and cleaned them with no luck and tried different vv/vw. I also have a cheap tank and it leaks every time I'm outside. I'm having zero luck lately and I'm so very frustrated and I'm getting close to my breaking point with it.

 

[Burn_notice_fan_NY]

It's not making contact. Grab a pair of tweezers and gently and barely pull the center pin on the clearo down.

 

[Burn_notice_fan_NY]

Cheap tank issue, is it a plastic tank? What flavor eliquid is in it?

 

[DetraMental]

Use a toothpick or a very small screwdriver and gently wiggle up and around the center connection pin inside the contact of the MVP2. If you put the clearomizer on too tight it will push this pin down and cause it to not make contact giving you the NON reading.

 

[jamie0516]

Cheap tank issue, is it a plastic tank? What flavor eliquid is in it?

Yeah its a plastic tank. It happens with every flavor I have but today was cotton candy with menthol. I mix menthol in everything

 

[v1k1ng1001]

You can't pry the pin on the aerobase down but you can clean up the contacts on your mvp and/or pry the center pin up a little bit so it makes contact. Make sure you assemble everything correctly so there isn't a short.

 

[Buggainok]

The MVP is really a quality device. Sometimes when you use off-brand, cheaper accessories with something nice, you may damage your good thing.

I remember breaking a boom box long ago by trying to play cheap off brand tapes in it. Also I was hanging very expensive wallpaper, and tried to be "cheap" and not use new fresh blades to cut it. Saved on razor blades - ruined some expensive wallpaper.

 

[Maestro]

If prying the pins doesn't work, try a 510-510 adapter or an ego-510 adapter.

 

[jamie0516]

The MVP is really a quality device. Sometimes when you use off-brand, cheaper accessories with something nice, you may damage your good thing.

I remember breaking a boom box long ago by trying to play cheap off brand tapes in it. Also I was hanging very expensive wallpaper, and tried to be "cheap" and not use new fresh blades to cut it. Saved on razor blades - ruined some expensive wallpaper.

That's definitely my concern with all this leaking going on. Ive only had the cheap tank for a few days and i doubt I will be using it again. I've been cleaning my battery constantly, even resorted to carrying my tank around unattatched between puffs. I've been using the cheap one while waiting for a replacement piece on my aerotank.

 

[jamie0516]

Hmm so I tried all of the advice but it only fixes the non reading sometimes and I'm still having to pull really hard. What am I doing wrong here

 

[Burn_notice_fan_NY]

When you tighten it, don't do it too tight. If it is the center pin issue, (which I'm guessing) then you might be pushing the center pin in too much each time you screw down. Buying a 510 to 510 adapter should do the job.

 

[thatmank]

This is why i got rid of my MVP. It got to the point i was having to fiddle with that pin every time i put a new tank on.
It got old. good luck.

 

[Maestro]

Back the tank off a couple of turns and try drawing on it. If it draws better, then the air holes are getting plugged. You likely over-tightened it.

 

[DetraMental]

It should only be finger tight, which isn't really tight at all. I just fixed a friends that the guy at the vape shop must have hand tightened. The entire tank came apart and the bottom was still stuck. I really had to work on her pin but it's working like a champ now since I told her how not to tighten it. I hope you get yours working right because it is a great device.

 

[livinlarge]

I use a MVP 2.0 and works fine with lots of tanks. Just snug it down. Not too tight


Sent from my iPad using Tapatalk

 

[PennyLynn]

I agree that the center pin can so easily be flattened. I got one of those 510-to-510 connectors and it helped a lot. Had no idea I was over-tightening.

 

[jamie0516]

If prying the pins doesn't work, try a 510-510 adapter or an ego-510 adapter.

Got my adapter in today and I am still getting the non reading. I pulled on the pins for that too and still no luck

 

[Hal]

Did you tighten up the coil yet.?

Sent from my XT1031 using Tapatalk

 

[Maestro]

Are you sure your coil is good? If it's popped you won't get any reading on it.

 

[EBates]

If you are seeing a resistance reading on the atomizer then the problem is that the air flow control is in the closed position. Turn the air flow control to open it. It is the knurled portion of the base of the aerotank.