Squonk Porn!

MyMagicMist

Ultra Member
ECF Veteran
Mar 28, 2014
1,159
2,465
53
You are about to begin a great adventure.

As long as I do not need to fool too much in the math, I'll be alright. Have learned about Ohm's Law, keep handy references. Not intending to do sub ohm coils below a net of .60 ohms as per advisement here. Actually kind of looking forward to it. :) Yes, got an ohm meter for testing.
 

Doffy

Vaping Master
ECF Veteran
Verified Member
Mar 15, 2014
8,220
40,975
Australia
Alright then, ...

I am in the process of doing two firsts with one stone. Just ordered $21.98 Terminator 18650 Drip Nebulizer Vaporizer Kit - 10ml / 1*18650 at FastTech - Worldwide Free Shipping . I had looked at another product and something about it just seemed off to me. Think it was the other product lacking a Pyrex tank oddly. Know that may seem a bit dumb given you don't need to see juice levels in a squonk RDA. Force of habit for me "get a Pyrex tank". Besides force of habit, I'll enjoy looking in on the coils as they make vaper. The kit is also a mech mod, so, that'll be another first. The other being this kit will be my first squonk kit.

Now, to figure out the DIY of juice and set about finding means to stock pile a bit. Will also need wire, thinking I'll
try rayon as wick. Planning an looking toward being as low end affordable as possible. May even go the route of unflavored 18mg/ml base. Can buy PG and VG in state if need be. Fairly sure I can buy nicotine either in state, or from out of state on line still. Nicotine is nicotine, not ejuice, at least I think I'm comprehending that correctly.

<sarcasm>Wish me luck dancing around with unprotected batteries in my pants pockets. ;) :)</sarcasm>

Congrats. FWIW you want stainless steel for atties. The smokeless owl thing you bought gets really bad reviews, like bin fodder bad. But the mod is meant to be a good starting point provided you stay over 0.5ohm.
 

MyMagicMist

Ultra Member
ECF Veteran
Mar 28, 2014
1,159
2,465
53
Congrats. FWIW you want stainless steel for atties. The smokeless owl thing you bought gets really bad reviews, like bin fodder bad. But the mod is meant to be a good starting point provided you stay over 0.5ohm.

Alright, sounds like it will fare to get me a start then. Will check out stainless atomizers. Have seen a few that come already made for squonking, others which require a custom center / positive post. For now I need to hold fast on stipend debits. Bought the kit and some juice this evening which took around half of stipend balance. Need it conserved for emergency cases.

More of a low maintenance person, yet figure I'm spending less on vaping than tobacco. Need durable gear and juice. Will not return to tobacco. Wife is happier I vape and a bit more accepting of it. Still, I had to wheedle her on this evening's shopping. Oh, I probably did not have to, figured courtesy could not hurt though.
 

Doffy

Vaping Master
ECF Veteran
Verified Member
Mar 15, 2014
8,220
40,975
Australia
Alright, sounds like it will fare to get me a start then. Will check out stainless atomizers. Have seen a few that come already made for squonking, others which require a custom center / positive post. For now I need to hold fast on stipend debits. Bought the kit and some juice this evening which took around half of stipend balance. Need it conserved for emergency cases.

More of a low maintenance person, yet figure I'm spending less on vaping than tobacco. Need durable gear and juice. Will not return to tobacco. Wife is happier I vape and a bit more accepting of it. Still, I had to wheedle her on this evening's shopping. Oh, I probably did not have to, figured courtesy could not hurt though.
The wife factor is an issue for many. I think it was rossum who suggested sending her shoe shopping with your credit card a week before vape mail

Sent from my GT-I9506 using Tapatalk
 

Mrrickyyap

Senior Member
ECF Veteran
Verified Member
Mar 24, 2013
259
473
San Francisco, California
The Kennedy 22 is meant to be a bottom fed rda in my opinion. Thanks to catfish atty mods for the modification.
f4e32f3ad64bffbf6235f5af8e7cb2c4.jpg



Sent from my iPhone using Tapatalk
 

Mrrickyyap

Senior Member
ECF Veteran
Verified Member
Mar 24, 2013
259
473
San Francisco, California
View attachment 534241
The hellfire predator is a BF or dripper. Got one inbound. Should be in my hands any day now. Top air. Lotsa air. Easy build and easy on the eye. I'm down.
Are those burs I see in the middle of the deck?


Sent from my iPhone using Tapatalk
 

super_X_drifter

ECF Guru
ECF Veteran
Verified Member
Oct 4, 2012
10,635
45,120
Somewhere out there
www.youtube.com
Are those burs I see in the middle of the deck?


Sent from my iPhone using Tapatalk
That was the preproduction prototype. Expecting none of that on a final hellfire product.
 

super_X_drifter

ECF Guru
ECF Veteran
Verified Member
Oct 4, 2012
10,635
45,120
Somewhere out there
www.youtube.com
Very nice SuperX! I'm hoping to score one from the next batch :)
Lol, yours sitting in Customs now?
I've got some awesome Vapemail coming today but it's not squonk related.


Sent from my iPhone using Tapatalk
Hell yeah - stoked that it is now in the ATL and should arrive at my crib tomorrow. Prolly shoot a movie on it over the weekend too.
 

73neb

Super Member
Supporting Member
ECF Veteran
Verified Member
Feb 27, 2014
671
6,114
N. California Bay Area
How is the copper one? Any funny


Sent from my iPad using Tapatalk
I've only had it built for a few hours, but nothing funny so far. I did put some Renaissance wax on it in the hope that the "dirty penny effect" would be avoided.
 

Users who are viewing this thread