Steam Monkey... Vaporizers for Steam Powered Humans!
- Thread starter Lance_Wallen
- Start date
- th_trl_thread_readers 0
- Status
Yup, you, Killnine and Boardopboy are sorta my only company in here. I need to put you on a recruitment drive or something
I am here. Mostly just kind of lurking at the moment since I do not need anything new. I am trying to spred word of your new site though. Great prices, good equipment.
if anyone is reading these that has used my mesh, I need to get some feedback. I've gotten 2 customers who are saying my mesh tastes bad. I'm ready to make another order but if this batch was 'bad' I'm not ordering from the same people.
Got my first Monkey order in this morning. Picked up an AGA-T...and if you're wanting one, you better act fast. Last night there were 8, when I got there this morning there were three. Now there's two.
Also picked up a ViVi nova head. I too hope to see some higher ohm heads.
Looking forward to business in the future!
Sent from my iPad using Tapatalk
Also picked up a ViVi nova head. I too hope to see some higher ohm heads.
Looking forward to business in the future!
Sent from my iPad using Tapatalk
Last edited:
I'm using some of your 400 I just got in yesterday. Its still breaking in, but it tastes just fine to me. I would think the people saying it tastes bad aren't giving it time to "cure"
Time to "cure"? I know about oxidizing the wick, but never heard about curing. Can you explain a bit?
Sent from my iPad using Tapatalk
I covered this pretty extensively in my other thread but I'll summarize here.
The folks complaining have don't actually 'torch' their mesh. Turns out there can be some residues on the mesh from the machining process used to make it at the factory. If you torch it, you burn any of these residues off. I always wash my mesh and coil wires before I use them, just an old habit. I made the mistake of assuming other people did this as well or at least torched it to purge it of any factory remnants.
They didn't and they got the same basic nastiness you get out of a new atomizer from china... I'm making a few changes to my mesh to help mitigate this in the future.
Got my first Monkey order in this morning. Picked up an AGA-T...and if you're wanting one, you better act fast. Last night there were 8, when I got there this morning there were three. Now there's two.
Also pi key up a ViVi nova head. I too hope to see some higher ohm heads.
Looking forward to business in the future!
Sent from my iPad using Tapatalk
I'm happy you got your order! More high rez vivi heads are on the way (literally... they are in boxes, on their way to me right now!).
Don't forget to keep an eye on my other thread for product updates and discussion. This thread will actually be closed in the near future to make room for my next contest. The thread linked below will be my 'constant' supplier thread
http://www.e-cigarette-forum.com/fo...ey-product-updates-discussion-join-troop.html
http://www.e-cigarette-forum.com/fo...ey-product-updates-discussion-join-troop.html
And I already got my tracking number. You sir, are on the ball!
Thanks Lance!
Sent from my iPad using Tapatalk
I just cleaned up the 5 'misaligned' Aga-T's I had left after matching all the caps. Air holes are pretty much centered on the SS Mesh wick hole now (couple milimeters off max).
I'm putting 5 more "in stock" in about 5 minutes, so if you're interested, get em while they last. I wont' be re-ordering them until I finish negotiating with the vendor for some improvements.
I'm putting 5 more "in stock" in about 5 minutes, so if you're interested, get em while they last. I wont' be re-ordering them until I finish negotiating with the vendor for some improvements.
- Status
Similar threads
- Locked
- Locked