Smoktech Variable Voltage Mod-VMax Body only
Sale price: $128.00
Quantity:
Smoktech Variable Voltage Mod-VMax Body only-Silver
Device measurement

iameter 21mm * length 110mm
Body material: Brass (this provides better electric conduction than stainless steel or aluminum)
Built-in three digit display allows you to visually adjust your voltage
Output Voltage: adjustable from 3.0v~6.0v in 0.1 volt increments
Discharge voltage: 6v~8.4v
Quiescent current: Step-down regulator
VMax can handle 5Amps or even larger current
Battery: 2 pcs IMR Nipple 600mah 18350 battery stacked in series. (different chemistry and safer), this battery is better for use in high current draw modules, but safer than ICR or other li-on batteries!
Available user setting :
Power adjust up
Power adjust down
Power on/off
Battery Check
Atomizer ohm check
LED on/off
Awesome pushbutton, no matter how you push it, it will not stick! Has a 10 seconds cutoff protection.
Warranty and Replacement info:
There is a 3 month warranty, beginning from shipping date, on defective parts or DOA. No Refunds. Physical damage is not covered by the return policy.
VMax User Settings
UU- Power up
UD- Power down
SO- Power on/off
UC- Battery Check
DS - display information setting
(- do- atomizer output voltage
-du- battery output voltage
-dR - atomizer ohm )
LO- LED on/off
Power Adjust Up:
1. Press the button 3 times in a row until "UU" is shown on the display.
2. When UU is shown on the display, leave the button idle for 2 seconds. The display will change to show the last voltage selected.
3. Once the voltage is displayed, each time you press the button the voltage will advance to the next higher setting: 3.1,3.2,3.3 etc. When you reach 6.0, it will rotate back to 3.0 and go up again.
4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.
Power Adjust Down:
1. Press the button 4 times in a row until "UD" is shown on the display .
2. When UD is shown on the display , leave the button idle for 2 seconds. The display will change to show the last voltage selected.
4. Once the voltage is displayed, each time you press the button the voltage will advance to the next lower setting: 5.9,5.8,5.7 etc. When you reach 3.0, it will rotate back to 6.0 and go up again.
4. when you have reached the desired setting, leave the button idle for 2 second. The setting will be saved and VV will resume normal operation.
Power On/Off:
1. Press the button 5 times in a row until "SO" is shown on the display.
2. When UD is shown on the display, leave the button idle for 2 seconds. The display will show the last setting, on or off .
4. Each time you press the button the display will toggle between on/off.
4. When you have reached the desired setting, leave the button idle for 2 seconds. If you selected "OF" the VV will go into standby mode.
Battery Check:
1. Press the button 6 times in a row until UC is shown on the display.
2. When UC is shown on the display, leave the button idle for 2 seconds, the digital display will show your battery voltage measurement.
3. The battery voltage will be displayed for 2 seconds, then the display will turn off.
Display Information Setting During Vaping:
1. Press the button 7 times in a row until DS is shown on the display,
2. When DS is shown on the display, leave the button for 2 seconds, the display will show the current setting: DO, DU or DR.
3. Each time you press the button, the setting will toggle among "DO" "DU" or "DR" ,
4. When "DO" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer working output voltage during your vaping;
5. When "DU" is chosen, leave the button idle for 2 second, the setting will be saved and the display will show your battery voltage during your vaping.
6. When "DR" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer resistance during your vaping.
LED On/Off
1. Press the button 8 times in a row until "LO" is shown on the display.
2. When LO is shown on the display, leave the button idle for 2 seconds, the display will show the current setting: ON/OFF .
3. Each time you press the button, the setting will toggle between on/off.
4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.
Short Circuit Protection:
The display will show the below error code when there is a short circuit:
1. F1: resistance for the heating coil of cartomizer is bigger than 0.5R, or smaller than 1.3R
2. F2: resistance for the heating coil of cartomizer is smaller than 0.5R
Recommended Cartomizer/Atomizer:
3V-4V for 1.5ohm,4V-5V for 2.0-2.5ohm,5V-6V for 3.0ohm.
Smoktech Variable Voltage Mod-VMax Body only - E Cig : Joye eGo & eGo-T | Boge Leo | Cartomizers | E-Liquid | Electronic Cigarettes | eGo Tank