SVD or Vamo?

[lorie]

Just as the title suggests. Vamo Or Innokin SVD? I am in the market for a mod. Since they are relatively similarly priced and both have imperfections I am unable to decide whether to get a Vamo or an SVD. Mostly to be used at home at the computer desk.

I already have an Innokin VV3 (which is great) for taking downtown with me and also have an as yet unused Smoktech SID so not looking for either of those. Wanting to stock up on mod's and VV models in case legislation outlaws vaping in this country in future months, so thought I would buy another VV MOD. I kinda like the quality of Innokin.. great build quality but I hear the SVD's are big and heavy for ladies (yes I am one).
Battery advice would be great too. I realize my SID needs flat tops but apparently a Vamo would need nipple tops. Is this correct?

 

[steved5600]

The SVD has crappy up down switches. The fall off. The Vamo which i have has a flaw in it's 510 connector. May only last a year if you change attys much. May i suggest going with the Zmax. It's a bit harder to make changes on but if you get the SS telescoping it's built like a tank.

 

[lorie]

Did not even think of a Zmax since I hear so much about the other 2 MOD's. Similarly priced I notice. Any flaws?
With the 510 connection problem on the Vamo a 510 to 510 connector could possibly help by protecting the threads (I hear the Vamo threads are not very good) although it would possibly make things unstable and ugly.. but I am only guessing.

 

[lorie]

What version Zmax are you suggesting steve?

 

[Ladiekali]

Very happy with svd.
I held a vamo once, laughed and handed it back

 

[yzer]

You would be much better off with a Sigelei Zmax V2, V3, or V5 than a Vamo or SVD if available in your region. The Innokin SVD suffers from under-designed and undersized switches, the Vamos have soft, weak metal for the 510 threading. Both are damned by long length. The Sigelei APVs have evolved beyond those weaknesses.

 

[Myxlpyxlx]

SVD is by far best cheap mod out there. Solid built and I mean sturdy, accurate ohm check and voltage selection and the telescopic battery tube is handy. Not to mention it has a 7 amp limit which lets you use down to .8 ohm attys. Vamo is junk imo had a v2 v3 and v5 all garbage. Zmax has the single button that just annoys me. Both of the 2 lesser only lets you down to 1.2 ohm. Vamo uses pudding for its 510 connection and its electronics are suspect. The Tesla is another one you may want to think about my lady friend loves hers as it's nice and light and has a unique look.

 

[coalyard]

I own an SVD and I can recommend it. It is not a 7 amp device, it is limited to 5 amps, and it will not fire below 1.2 ohm. It is very well built, the buttons function as they should. You can use any (18) battery with it. I use (2) 18350 most of the time because they last a full day without re-charging. I cannot comment on the VAMO as I do not own one, and I haven't tested one extensively.

Hope this helps, and welcome to ECF!

 

[yzer]

Innokin SVD is overpriced, oversized and under-designed. You can get a Sigelei Zmax V3 for $39.95 from Desert Vapes with fast US shipping. $7 more will get you a V5 from the same. Telescopic tube on V3 and V5 fits 18350, 18490, 18500, 18650, 2x18350. Single button menu rocks. More cheap switches on the SVD mean more chances for failure. I've been using a Sigelei V3 for 14 months, now.

 

[edyle]

Just as the title suggests. Vamo Or Innokin SVD? I am in the market for a MOD. Since they are relatively similarly priced and both have imperfections I am unable to decide whether to get a Vamo or an SVD. Mostly to be used at home at the computer desk.

I already have an Innokin VV3 (which is great) for taking downtown with me and also have an as yet unused Smoktech SID so not looking for either of those. Wanting to stock up on MOD's and VV models in case legislation outlaws vaping in this country in future months, so thought I would buy another VV MOD. I kinda like the quality of Innokin.. great build quality but I hear the SVD's are big and heavy for ladies (yes I am one).
Battery advice would be great too. I realize my SID needs flat tops but apparently a Vamo would need nipple tops. Is this correct?

For use at home at computer desk, you might want to pick up a couple of these.

I have a vamo; I recommend it; but after 3 months I did have to take the top off to replace the center pin insulator;
they have a reputation for 510 threads getting stripped out but I haven't had that problem.

The svd I'm wary about because of reviews, but it is telescopic with continuous thread (you telescope by screwing in) with no spring; that's one notable difference compared to the vamo.

 

[yzer]

Here are my three Sigeleis. Left: V5 purchased this April from Desert Vapes. Sized for 18500 with IBTanked on top. Center: First generation 14 month-old V3 purchased from ElectronicStix in April, 2013. This one has seen a lot of use. Right: Second generation V3 purchased from 101 Vape in December of 2013. This one has the short battery cap installed for 18350.

This shot gives you a good idea of how well the brushed stainless steel has held up to wear. You can see slight variations in the finishes and trim. Each is a little different.

Compare these sizes with Vamo or Innokin SVD...

These Sigeleis are 23mm in diameter.
18350: 100mm with short battery cap, 105mm with long battery cap.
18490: 111-114mm with either battery cap, spring 1/2 compressed.
18500: 112-115mm with either battery cap, spring 1/2 compressed.
18650: 127-130mm with either battery cap, spring 1/2 compressed.
2x18350: 132-135mm with long battery cap, spring 1/2 compressed.

 

[edyle]

Did not even think of a Zmax since I hear so much about the other 2 MOD's. Similarly priced I notice. Any flaws?
With the 510 connection problem on the Vamo a 510 to 510 connector could possibly help by protecting the threads (I hear the Vamo threads are not very good) although it would possibly make things unstable and ugly.. but I am only guessing.

I have a zmax and a vamo; I use the vamo because of the convenient interface; the zmax is a 1 button interface. i can also check atomizer resistance on the vamo by holding down the + button so it checks resistance without putting full power to the coil whereas the zmax you have to put full power to the coil to check resistance.

 

[yzer]

Sigelei Zmax V5 display can be configured to show atomizer resistance under power, but you can get a flash reading without making the atomizer fully heat (sizzle). It will also show current, draw time, puff counter, vaping voltage or watts and battery voltage.

 

[Bunnykiller]

the SVD is a tougher unit than the Vamo
I had 2 Vamo3's, both died from drops of 2-3 feet
the 510 threads are soft and wear out quickly

the SVD has taken many falls and bumps and is still going strong
the 510 threads on a SVD are SS ( wont wear out like the Vamos)

the SVD can fire off a .8 ohm coil, the Vamo sez no to 1.0 or less...

but if you get the Vamo and drop it and it dies, you can make a mech out of it...

 

[jaxgator]

I just got an SVD this past week. Holy hell! That thing is long! It's got to be at least a foot long with a Nautilus sitting on top.

 

[K_Tech]

I have a Vamo (V3) and an SVD.

After a month, the 510 connector in the Vamo stripped out completely. However, after a $6 replacement top cap and ~20 minutes with a strap wrench and a soldering iron, it's still going strong.

My first SVD failed electrically after about a month. Its replacement started having button issues within a few weeks. It now sits in the vape cabinet waiting for the day I feel like messing with it.

I would suggest going with a Sigelei.

 

[GPC2012]

I have one of each, actually a V3, if price is a concern you can get the V3 at Desert vapes very reasonably.

 

[Asbestos4004]

If you're preparing for a possible ban, I'd suggest saving your money for a month or 2 and buying a quality device that has a warrantee and can be repaired if needed. You'll pay more up front but less in the long run. I'd also pick up a few mechanicals and rebuildable attys. You'll always be able to buy batteries, wire and cotton. All of the suggestions you've been given are fine if you're just looking for another mod to use. If your looking for something to last a few years, it hasn't been suggested yet.

 

[Cool-breeze]

If you're preparing for a possible ban, I'd suggest saving your money for a month or 2 and buying a quality device that has a warrantee and can be repaired if needed. You'll pay more up front but less in the long run. I'd also pick up a few mechanicals and rebuildable attys. You'll always be able to buy batteries, wire and cotton. All of the suggestions you've been given are fine if you're just looking for another mod to use. If your looking for something to last a few years, it hasn't been suggested yet.

Exactly my thoughts! They only way I would differ it is I would say go ahead and buy a decent mech/ rebuildable atty now just incase. Then save up for something special.

 

[KenD]

The SVD. Mine's been fully functioning for almost a year now (though I mostly use mechs nowadays). Been dropped, spilt beer on it etc, and it's still going strong. No problem with the buttons either. I had a Vamo v5, but I dropped it six days in and it broke. Might just have been a flawed unit.

Sent from my GT-I9100 using Tapatalk