Tank Question

[themysterious1]

I would like to know where I could buy the dual coil cartos for either the COV DCT tank or the liquidator tank. I know they cant have the black stickers on them I have looked at a few places and they all just seem to have the black sticker ones.Would like to buy them in packs instead on just single if possible.I guess I could drill my own holes if I could just find them without the stickers so they dont have to be slotted I have watched tons of vids on this and I think drilling the hole is the easiest with a 1/16 drill bit.Any help would be appreciated.Or if you have a trick to get the sticker and sticky stuff off Im open to that also.Thanks One last question what ohms would u recommend for a Provari have one in the mail.

 

[WomanOfHeart]

You can buy the DCCs with stickers on them and just take them off. Take the residual adhesive off with some 91% Isopropyl Alcohol. If you'd rather not do that, then you can buy some DCCs from VaporEscence or MostAngryIndustries.

You can buy any ohm cartos that you want with the Provari because you dial in the voltage. The DCCs work well with any voltage from 3.7 to 6V. I've been using the Liquinator DCC tank at 5 and 6V and I love it!

 

[sfkid]

You can buy the DCCs with stickers on them and just take them off. Take the residual adhesive off with some 91% Isopropyl Alcohol. If you'd rather not do that, then you can buy some DCCs from VaporEscence or MostAngryIndustries.

You can buy any ohm cartos that you want with the Provari because you dial in the voltage. The DCCs work well with any voltage from 3.7 to 6V. I've been using the Liquinator DCC tank at 5 and 6V and I love it!

Actually, be careful with LR cartos because you can NOT vape them at any voltage you want. The provari has a cut off, dont remember the exact wattage but with 1.5Ohm cartos you will NOT be able to push past 3.9 volts.

 

[WomanOfHeart]

DCC's aren't the same as LR cartos. I've been using the DCC's at 3.7, 5 and 6V without any problems on my Liquinator tank. With a ProVari, you can dial in any voltage you want with the DCC's, it's just a matter of choosing which one suits you better.

 

[Devonmoonshire]

Actually, be careful with LR cartos because you can NOT vape them at any voltage you want. The provari has a cut off, dont remember the exact wattage but with 1.5Ohm cartos you will NOT be able to push past 3.9 volts.

DCC's aren't the same as LR cartos. I've been using the DCC's at 3.7, 5 and 6V without any problems on my Liquinator tank. With a ProVari, you can dial in any voltage you want with the DCC's, it's just a matter of choosing which one suits you better.

I get mine from a local, (if you can call 65 miles away local, which I do because it is well worth the drive), shop called E-Cig City in Laguna Beach.

I do use Most Angry Pirates new Stainless Steel DC Tank with the dual coils, both the ones that register at 1.5 ohms and the ones that register at 2.0-2.2.

With the Lower resistance ones I have been able to get the Provari as high as 4.4 volts without it erroring out. much higher than that and it does in fact cut out, however with a straight non variable mod at 5 or 6 volts they do perform just fine from my experience.

I take the the higher resistance dual coils all the way up to 6 volts with the Provari though with absolutely no issues.

Hope this helps clear this up;
Nate aka Darth Vapor

 

[themysterious1]

Thanks I would like to know where to get some also.

 

[Sedateme]

Like WomanOfHeart mentioned, you can take the black stickers off of your cartos pretty easily. I wasn't able to remove the adhesive with IPA myself, but some WD-40 sprayed on a paper towel takes it right off. Then give it a quick swipe with the IPA to clean up the WD-40 a little, punch a hole/cut a slit, and good to go.

 

[Devonmoonshire]

Okay Okay, Here is where you can get pre punched Dual coil cartomizers. This is also a supplier here on ECF and he has his own thread so you can ask him any questions you like as well very easily.

XL Punched Dual Coil Cartomizer

Hope this is what you are looking for my Friend;
Nate aka Darth Vapor

 

[themysterious1]

Okay Okay, Here is where you can get pre punched Dual coil cartomizers. This is also a supplier here on ECF and he has his own thread so you can ask him any questions you like as well very easily.

XL Punched Dual Coil Cartomizer

Hope this is what you are looking for my Friend;
Nate aka Darth Vapor

Thanks that was what I was looking for.

 

[Devonmoonshire]

My Pleasure, I figured you might like those, I just had to get enough coffee into my Braincells to activate the memory circuits and remember where I saw them

Nate aka Darth vapor