- Status
I'll give a stab at answering this one.
More consistency seems to be the most general way to say it. They should be a bit less "airy". They all come with the newer o ring seals on them, so you won't have to swap them out. Some people had trouble with off center or bunched up coils on the first run--and that could have lowered life of the atty. There is an internal wire change, too --- a little above my technical understanding----but it was a requested change, I believe, by some users.
Is Vapage EVER going to update their site?
I'm holding off of more Silos hoping new stuff will inspire me to reach for the free shipping
This weekend I will have to go back to my eGo until I get more Silos.
Looking for extra bottles and seal kits too.
Vmod is wanting a new skin too, I'm sure
I'm holding off of more Silos hoping new stuff will inspire me to reach for the free shipping
This weekend I will have to go back to my eGo until I get more Silos.
Looking for extra bottles and seal kits too.
Vmod is wanting a new skin too, I'm sure
I think they have all the new products in there warehouse already, just not on the site yet. You can try calling them and ordering through the phone. I ordered a 14500 charger through the phone yesterday even though its not on their site.
The one around the atty?
Once it's wet with juice, it's not going to seal as well. Going back to our original claims of a nice soapy VMod bath makes for a happy VMod. Make sure to wipe down the attys & clean the seals too. A slippery seal just isn't going to stop juice like a clean seal.
I know that dark colored, sweet juices are frustrating. There is no atty or carto made which will stand up to it. I know it tastes good, but it's a fact light or clear juices aren't as hard on heating coils. I love Vaperite's VR4, but the stuff gunks up a new carto faster than you can say AG.
in an email from vapage they said they would have a brand new website on monday. I was asking about buying a pack of replacement seals he said that they weren't on the site yet but they planned to have them up on their "brand new site on monday"
Ya I tried turning it inside out worked for a bit but not long. I think gh's method of cutting so the that the ends are perfectly flat might be the key. I had tried using a cut condom before but the ends were a bit wavy from my cutting.
This post might be helpful to you (and anyone else that is more of a newcomer to VMODia): http://www.e-cigarette-forum.com/forum/e-cigarette-video-reviews/195396-vmod-107.html#post3869331
Beaver, you might try cutting one just shy of 3/16" to see if that works better. Make sure when you thread your atty/ carto into the Vmod that you don't over tighten. Just let it bottom out, don't torque it down. If you over tighten the bottom seal will curl up and cover the slots that allow the juice to flow into the atty/ carto. Also if your outer seal gets pushed down too far it also covers the juice slots. When either of these happen the juice has no where to go and the pressure pushes it past the seals and you get leaks....
Just a heads up on this. I did order a few of the TPA 3ml bottles and they do NOT fit at all, not even slightly. They will not thread onto the VMOD. I'm happy Vapage will carry them in the correct size. I have no idea how Mim got these to work, but I have to say...
Well, looks like i've found extra bottles for our beloved Vmod.
These 3ml bottles arrived today from TPA. Threading is obviously different, but they move in fine and stay in place. After 5 hours of regular use, the only leak happened when i took it out, and not a really a leak, just a few drops on the thread.
On the left, TPA 3ml bottle with dropper and cap. Vmod included bottle on the right
Just a heads up on this. I did order a few of the TPA 3ml bottles and they do NOT fit at all, not even slightly. They will not thread onto the VMOD. I'm happy Vapage will carry them in the correct size. I have no idea how Mim got these to work, but I have to say...
Probably why his VMod was leaking.
Both of mine are dry & work great with the new chassis & seals.
just received the vapage 14500 battery charger, how long does it take for the batteries to fully charge? there doesnt seem to be an indicator on it to let you know if they are fully charged or not.
She's a happy little bugger
She's a happy little bugger
Oh, right, another minus for the new chasis i forgot to say. Those worked fine on the first chasis, but they don't on this new one.
So it "killed" my 2 bottles, and TPA ones didn't work.
Just....bleh.
So it "killed" my 2 bottles, and TPA ones didn't work.
Just....bleh.
Just a heads up on this. I did order a few of the TPA 3ml bottles and they do NOT fit at all, not even slightly. They will not thread onto the VMOD. I'm happy Vapage will carry them in the correct size. I have no idea how Mim got these to work, but I have to say...
just received the vapage 14500 battery charger, how long does it take for the batteries to fully charge? there doesnt seem to be an indicator on it to let you know if they are fully charged or not.
She's a happy little bugger
Don't the eyes light up?
They look like they should.
Edit: beat ya tearose!
Those "eyes" on the charger look to me like they are lights. I would think they would light up and change color when charged.
I have drained the batteries already since I got the vmod a couple weeks ago, I was waiting for my charger to come in but it hasen't yet so I called vapage and ordered one from them, i got tired of waiting for my wf-188
- Status
Similar threads
