RDA Thinking about getting a new rda.

[LuNar]

Hi guys.

My current set up is a tugboat clone and a ipv mini v1. I made a good dual coil set up at 0.5 ohms and firing at 30 watts, it preforms well. Great flavor and really big clouds.

My problem is when my rda starts to heat up, it heats up my mod. I really don't like this. I also don't like how my chimney and top cap are all one big piece. So if I need to drip more eliquid, I will always get some eliquid on my mod when I go to put the chimney back on. I'd like to be able to drip through the drip tip, if that makes sense.

I've seen some rda's that have a removable top cap, that is separate from the chimney, or body section, and they can drip right on to their coils/wick without getting eliquid on the mod. I really want one that can do this.

1. I want a rda with heat sinks on the bottom to stop heat transfer from my rda to my mod.
2. Produces a nice medium between flavor/vapor.
3. I like using dual coils or singles, quad is just not my thing.
4. I like a warm to hot vape, not scorching hot.
5. Reasonability easy to build on. I'm comfortable with horizontal coils I have not tried vertical coils yet.
6. Preferable adjustable airflow but if the rda has plenty without it then it's not a problem. I like a good open airy draw.
7. I'd like a removable drip tip section/top cap section for easy dripping access.

I was thinking about getting an authentic tugboat v2 but I noticed it does not have heat sinks on the bottom to stop heat transfer. I've also looked into the infinite CLT v3 and I like just about everything about it but.. it's just tall. I'm not really a big fan of it being so tall.

I just want to know if you guys know of any rda's that would better suit me.

 

[Necrotic]

The haze rda is great using it right now. Great flavor and great clouds. Doesn't have any heat sinks but I've never noticed mine even get warm even after Vaping constantly. It has a t center post so easy to build single, dual or quad. It's a very good rda. Come with a delrin covered ss drip tip or you can use your own.

 

[LuNar]

Thanks man I've never heard of it, I'll check it out soon.

 

[drippaboi]

You could also use a Vulcanizer to add effective bottom heat-sinking to any 510 RBA. I use one with my Magma and it makes a noticeable impact on heat transfer down to the MOD.

 

[Hdivr]

Check out the review for the Hobo v2......... no heat sink but holds a lot of eliquid. Pull the top cap off and drip right on the coils. Unscrew the body and super easy access to coils.

I've used a hobo clone exclusively for a few months now and have only set it aside because I am liking my Kanger Subtank Nano just as much.

 

[LuNar]

I didn't know there was a such thing as vulcanizer.. Sweetness.
Ya I've been looking at the hobo v2. Might end up getting it, or the tugboat v2 lol I can't ever make up my mind.

Thanks guys.

 

[Necrotic]

I will warn you about the hobo clone. The positive post copper piece is very flimsy and will strip easily. I had mine for a day and built 2 coils before the thing stripped out and became useless and another guy at the shop I bought it from had the same problem as well.

 

[Sexy Syndra]

Aeolus, Aeolus, Aeolus. I just got mine in the mail 3 days ago and I can easily say this is the best atty I've every used. Doesn't spit, easy to build on, great flavor, and it has the heat sink on the bottom that you're looking for. Personally, I dislike the tugboat. I don't have many good things to say about it after using it for two months... so either check out the Aeolus (which happens to be cheaper than your options there), or the CLT v3.

 

[reeftivo]

Kennedy. Big under coil air flow, wide bore delrin drip tip, very deep well, easy build and great flavor. No need to pull the cap. Drip straight through and enjoy. I rock mine at 0.2 ohms and have no appreciable heat transfer to the mod.