Todays GGTS/AVS Experiment Findings WOW
- Thread starter mwa102464
- Start date
- th_trl_thread_readers 0
- Status
I smoke like this 1/2 now. The best thing is that atomizer fits exactly where we want on the top cap. The mouthpiece fits too!!! And yes it works well only in the position we normally smoke!
And the best thing is that it works but I dont know how
I will keep smoking like this to find out what is happening
A very nice thing too is that GGTS still has the same length even if the 801 atomizer is much bigger than the 901
ps..... also if you put a 11/2 o-ring between the 2 caps it would be better for 801 atomizer
ps2...... mwa, are you a genious my friend???!!!!!!!
And the best thing is that it works but I dont know how
I will keep smoking like this to find out what is happening
A very nice thing too is that GGTS still has the same length even if the 801 atomizer is much bigger than the 901
ps..... also if you put a 11/2 o-ring between the 2 caps it would be better for 801 atomizer
ps2...... mwa, are you a genious my friend???!!!!!!!
Last edited:
Ok, I found
The collector tank is flooding because atomizer has a width at 11,5mm and the hole that goes through the collector tank is a little bigger. That allows the liquid to go slow into the collector tank. Then atomizer is feeded from there. Its like when I said that you can put 10 drops inside the collector tank and you can use it as AVS with out AVS.
Exellent trick mwa. The only that cant fit very well because it has smaller hole is the mouthpiece but it screws enough for what we need to do there. The gap between the 2 caps is now 2mm instead of 1mm that was with the 901 atomizer, so its still more than ok.
ps........ Now if you have a burn taste (I dont have any for more than 1/2 now) you can refill the collector tank by blowing air 1-2 times on the mouthpiece and not suck air like the previous set up with 901.
The mwa's set up is working for me too but maybe it depends on the thickness of liquid but maybe not. We have to try more liquids for this set up because we have to see if collector tank is overflooded and start leaking. But so far so good
The collector tank is flooding because atomizer has a width at 11,5mm and the hole that goes through the collector tank is a little bigger. That allows the liquid to go slow into the collector tank. Then atomizer is feeded from there. Its like when I said that you can put 10 drops inside the collector tank and you can use it as AVS with out AVS.
Exellent trick mwa
. The only that cant fit very well because it has smaller hole is the mouthpiece but it screws enough for what we need to do there. The gap between the 2 caps is now 2mm instead of 1mm that was with the 901 atomizer, so its still more than ok.ps........ Now if you have a burn taste (I dont have any for more than 1/2 now) you can refill the collector tank by blowing air 1-2 times on the mouthpiece and not suck air like the previous set up with 901.
The mwa's set up is working for me too but maybe it depends on the thickness of liquid but maybe not. We have to try more liquids for this set up because we have to see if collector tank is overflooded and start leaking. But so far so good
Last edited:
Not sure which one is 11/2 o-ring, but this setup (although the idea is nice) is not working for me (liquid is use atmo is Totally Wicked's Patriot's Range Tobacco Americano). It's going too fast from main tank to the collector tank, i get it flooded fast and a leakage follows from the vent holes.
booker you only want to open the control ring a little bit. I have mine open maybe a 1/4 turn. Also, Make sure you have your tank and top caps on tight.
Harpo is right Booker my good friend. If you open a little the CR then air cant push liquid to fast to the collector tank. Maybe of course you use a thin liquid. Try again and we will see how it will go. I am still ok after 2-3 hours.
Be careful with this set up when you unscrew the AVS because atomizer gets unscrewed too. But it has different threads than the collector tank so you will damage the GG connector soon. So first take off the o-ring between the 2 caps and then unscrew the AVS. Then unscrew the atomizer.
Be careful with this set up when you unscrew the AVS because atomizer gets unscrewed too. But it has different threads than the collector tank so you will damage the GG connector soon. So first take off the o-ring between the 2 caps and then unscrew the AVS. Then unscrew the atomizer.
This is the way I take mine apart with this setup and the original setup. Haven't had an atomizer unscrew yet. Also remember when you tighten up the telescope to be careful because you can short the atomizer out if you tighten too much.
Thats true for all atomizers when we use them without AVS. Good to remind this Harpo my friend
6V till the atty gets old then 7.4.
I have a bunch of BE112s but I usually vape them at 5 volts with my GGTS passthrough. I'll have to try them at 6 volts. How are the holding up so far with the AVS?
Cool discovery mwa you mad scientist lol, going to try this myself as I have a shed load of 801's
Also, with MWA's trick the atty is not very in centre with the top of AVS. It goes strained when the top o-ring goes in.
You guys test this well, I stay with my 901-801 adapter for the time being
No problems with that here with 510 lid o-ring. Both with the HG's adapter and MWA's method.
- Status
