so these dry pulls, i dont fire it up when i do that do i?
also is it vg or pg i get to thin it out?
- Status
so these dry pulls, i dont fire it up when i do that do i?
also is it vg or pg i get to thin it out?
Nope, you don't need an lr if you're vaping VV. I heard that Boge was coming out with an XXL single coil carto that will fit these tanks, not sure when. IMHO, for a flawless vape, I cut down all of my tanks with a tube cutter and use Boge sr cartos. That has been my answer to get the most carefree vape possible. Just my .02.
Cutting down the tube, Lesson 1 according to my4jewels
If you're not sure how to cut down a tube, here are some instructions. I use a wood dowel inside the tube that is closest to the id of the tube. I use a wood dowel because it will not dull the blade when it's all of the way through the tube and hits the dowel. Use a tube cutter, inexpensive at any hardware store. Carefully turn the tube and dowel while increasing the pressure of cutting blade by turning the end of the cutter. Repeat until it is cut through. Just go slowly, turning the tube around and around. Watch carefully to be sure you are getting a straight cut as you turn it. Before you know it, you'll see the blade start to separate the tube. Just keep going until it's cut through all of the way around.
I use this type of pipe cutter, though not necessarily from this vendor. Mine is a pipe cutter almost identical to the one in the pic that my dad has had for years.
Copper pipe cutter ZR 32 6-32 mm | Contact VIRAX[/QUOTE]
Priming your Boge carto, Lesson 2 according to my4jewels
One or two small holes on a Boge sr carto. I use a rubber end cap from the carto and fill with about 15 drops. Put the carto in, batt side down, and let it soak up the juice. Blow out the carto from the open side to make sure no juice is in the air tube. Put on a drip tip, put the carto in the tank and take a few draws on it without power, just until you're getting some flavor. Power up your lavatube, and it should be perfect vaping!
Cutting down the tube, Lesson 1 according to my4jewels
If you're not sure how to cut down a tube, here are some instructions. I use a wood dowel inside the tube that is closest to the id of the tube. I use a wood dowel because it will not dull the blade when it's all of the way through the tube and hits the dowel. Use a tube cutter, inexpensive at any hardware store. Carefully turn the tube and dowel while increasing the pressure of cutting blade by turning the end of the cutter. Repeat until it is cut through. Just go slowly, turning the tube around and around. Watch carefully to be sure you are getting a straight cut as you turn it. Before you know it, you'll see the blade start to separate the tube. Just keep going until it's cut through all of the way around.
I use this type of pipe cutter, though not necessarily from this vendor. Mine is a pipe cutter almost identical to the one in the pic that my dad has had for years.
Copper pipe cutter ZR 32 6-32 mm | Contact VIRAX[/QUOTE]
Priming your Boge carto, Lesson 2 according to my4jewels
One or two small holes on a Boge sr carto. I use a rubber end cap from the carto and fill with about 15 drops. Put the carto in, batt side down, and let it soak up the juice. Blow out the carto from the open side to make sure no juice is in the air tube. Put on a drip tip, put the carto in the tank and take a few draws on it without power, just until you're getting some flavor. Power up your lavatube, and it should be perfect vaping!
Well I just cheat and buy tanks the proper size for single coil cartos. There are plenty of them on the market to choose from, but I like the J-TANK .
The build quality is far better than those mass produced tanks coming out of China.
However you can simply put a 10mm shorty extension on a Boge carto and it will fit in a DCT.
Here is a good video on how to fill a new carto in a tank. Juice is forced into the carto when you put the top cap back in.
http://www.youtube.com/watch?v=BPMlexANLXs&feature=player_embedded
The build quality is far better than those mass produced tanks coming out of China.
However you can simply put a 10mm shorty extension on a Boge carto and it will fit in a DCT.
Here is a good video on how to fill a new carto in a tank. Juice is forced into the carto when you put the top cap back in.
http://www.youtube.com/watch?v=BPMlexANLXs&feature=player_embedded
Last edited:
Priming your Boge carto, Lesson 2 according to my4jewels
One or two small holes on a Boge sr carto. I use a rubber end cap from the carto and fill with about 15 drops. Put the carto in, batt side down, and let it soak up the juice. Blow out the carto from the open side to make sure no juice is in the air tube. Put on a drip tip, put the carto in the tank and take a few draws on it without power, just until you're getting some flavor. Power up your lavatube, and it should be perfect vaping![/QUOTE]
???fill with about 15 drops. Put the carto in, batt side down, and let it soak up the juice. Blow out the carto from the open side to make sure no juice is in the air tube???
u lost me right here, if i let it soak up the juice, then blow in the open end, the juice it just soaked up will come out right?
One or two small holes on a Boge sr carto. I use a rubber end cap from the carto and fill with about 15 drops. Put the carto in, batt side down, and let it soak up the juice. Blow out the carto from the open side to make sure no juice is in the air tube. Put on a drip tip, put the carto in the tank and take a few draws on it without power, just until you're getting some flavor. Power up your lavatube, and it should be perfect vaping![/QUOTE]
???fill with about 15 drops. Put the carto in, batt side down, and let it soak up the juice. Blow out the carto from the open side to make sure no juice is in the air tube???
u lost me right here, if i let it soak up the juice, then blow in the open end, the juice it just soaked up will come out right?
ok watched the vid, ill give it a shot when im home,but again if my juice is too think then what?
add PG or VG ?
add PG or VG ?
You will find that most of us have our own favorite products and techniques. It's all good. The most important thing is that you find what works best for you. There seems to be more than 1 way to accomplish the same goal. You'll find your "path to enlightenment" if you stick with it.
VG is very thick -- you'll want to thin a juice using PG, distilled water, or vodka/grain alcohol. (If you use h20 or alcohol, only use a few drops.)
I went through three cartos in my Smoktech tank when I first started with it, and it was discouraging. But once I got it working it's been hassle-free for weeks. It's worth it.
I went through three cartos in my Smoktech tank when I first started with it, and it was discouraging. But once I got it working it's been hassle-free for weeks. It's worth it.
You will find that most of us have our own favorite products and techniques. It's all good. The most important thing is that you find what works best for you. There seems to be more than 1 way to accomplish the same goal. You'll find your "path to enlightenment" if you stick with it.
lmao path to enlightinment, nicely put...lol
so what do you recomend, do you thin ur juice? if so with what
I thin some of my recipes with vodka. I'd use PGA, but they don't sell it here in Ohio.
I also agree with Jewels about finding the way that works for you. A lot of people find that slotting doesn't work as well as punching for them. For me it's the opposite. I really tried to make the saddle valve carto punch method work, but slotting just does better for me. I don't get flooding, and the juice wicks perfectly. People use all sorts of different tanks, cartos, and juices though, so each variable is going to affect the solution that works.
Just expect that you are going to ruin some cartos before you find *the* technique. Maybe you will be lucky and figure it out right away, but you will probably ruin a few on your way to tank nirvana.
I also agree with Jewels about finding the way that works for you. A lot of people find that slotting doesn't work as well as punching for them. For me it's the opposite. I really tried to make the saddle valve carto punch method work, but slotting just does better for me. I don't get flooding, and the juice wicks perfectly. People use all sorts of different tanks, cartos, and juices though, so each variable is going to affect the solution that works.
Just expect that you are going to ruin some cartos before you find *the* technique. Maybe you will be lucky and figure it out right away, but you will probably ruin a few on your way to tank nirvana.
lol nirvana, lmao ok well i guess ill start with the blowing method first on the sloted one that stay dry, then ill dilute some juice, and go from there ty all for all your help
- Status
Similar threads
