Ufs

[dirfm]

Okay. I carefully built up my ufs with a nice atomizer, filled her up, and proceeded to watch all the juice run out of the air control. Never got a good vape, just mouthfuls of juice before it leaked out. Is there some video i can watch? I already use the ody short and drip and a few genesis mods...i must be doing something wrong.

 

[JollyRogers]

Was the juice control open when you screwed your atomizer in? Then once it is seated, completely close the juice control. I also have the air control closed when I fill.

Videos... all you need: UFS Feed System Tutorials | The Golden Greek Ecig

 

[dirfm]

The air control was closed when placing the atomizer and when filling. I will check out the video.

 

[JollyRogers]

Ok, but was the juice control open so the atty could seat all the way? A new UFS owner will leave the juice control closed sometimes when installing the atomizer. This prevents it from seating all the way. You think it is screwed in, but it is isn't sometimes... Hopefully the vids are of some help

 

[dirfm]

I bet that was the problem. I did have it closed when i seated it.

Guessing when i opened it a little..the pressure forced the leak because i know i sealed ot well.

The video did help some...i will try again. Thank you for all and any tips. Was very frustrated.

 

[fright88]

For Assembly I use the following steps.

Pull center pin out slightly (Not much you just want to make sure it doesn't hinder the atty from being seated all the way)
Close air controll (Habit Mostly)
Open juice controll all the way.
Screw on atomizer firmly.
Push center pin in to make contact.
Close juice controll all the way.
Finish assembly and fill.

If the center pin is binding on unlubed o-rings if can cause the atomizer not to seat al the way which will cause the juice controll to not seal properly. Also closed juice controll durring assembly can do the same thing.

Good luck

 

[dirfm]

I was wondering about the firing sin also as i was watching one of the mentioned videos. Thank you.

I an almost positive that i had it not fully seated and bad pressure.

 

[agp01]

Just have my hands on ufs, using ikv atomizer... The air suction is very tight.. Open up airflow control helps abit.... Still very tight for me....

Any1 have use it with ikv? So far no leaking...

 

[Keeno]

Just have my hands on ufs, using ikv atomizer... The air suction is very tight.. Open up airflow control helps abit.... Still very tight for me....

Any1 have use it with ikv? So far no leaking...

IKV attys very popular but for me I had the same issue as you on multiple devices....draw just way too tight for my liking.

 

[imeothanasis]

check the 4 holes on UFS connector and the 4 holes of CT agp. They have to be clear, so put a pin inside them to check if they are open

 

[agp01]

check the 4 holes on UFS connector and the 4 holes of CT agp. They have to be clear, so put a pin inside them to check if they are open

Thank you my friend, Imeo.. I redo everything again... N change to a diff atomizer... It's quite ok on joye atomizer... I guess ikv atomizer air draw is meant to be tight.....

 

[imeothanasis]

some atomizers have a hard draw and some of them are bad made agp. If the ceramic inside them has smaller holes or the wires that go through the ceramic's holes sit in a posisition that prevent air to come nice via them then you will experience this problem.

 

[agp01]

some atomizers have a hard draw and some of them are bad made agp. If the ceramic inside them has smaller holes or the wires that go through the ceramic's holes sit in a posisition that prevent air to come nice via them then you will experience this problem.

Thanks IMeo. Now I have better understanding if ufs! It's a great tank, y discontinue?

 

[imeothanasis]

yes, its discontinoued agp. Its the best tank ever for china atomizers but I am focusing now to rebuildables.

 

[Mosin_Sergei]

Wick 7mm., 1.6 Ohm

 

[agp01]

Wick 7mm., 1.6 OhmView attachment 119566View attachment 119567View attachment 119569

Patriot atomizer, my fren?

 

[Mosin_Sergei]

Yes agp01
Patriot is an atomizer.
Here's a clearer picture.
Top view of Patriot atomizer.
Installation of a double coil of 1.8 ohms

 

[agp01]

View attachment 119744
Yes agp01
Patriot is an atomizer.
Here's a clearer picture.
Top view of Patriot atomizer.
Installation of a double coil of 1.8 ohms

Thats a piece of beast that always not in stock.. lol... love it bud!

 

[Jalippo]

Can I buy somewhere sleeves for io6 and 306 to use them with my UFS V2

Sent from my GT-I9300 using Tapatalk 2

 

[Killjoy1]

There are a couple of options. One is these sleeves: http://www.gratefulvaper.com/the-sleeve.html

I've also used these, but they don't always work for UFS use, it's kinda hit or miss depending on the exact fit between the atty and adapter: 306 to 510 Drip Tip Adapter - Avid Vaper