So I just ordered my first kit to build an unregulated box mod. My question is...dual series or dual parallel and your reason why?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Unregulated box mod in series or parallel
- Thread starter Wheelin247
- Start date
- th_trl_thread_readers 0
- Status
Parallel if your builds are lower (like .15-.25) series for higher ohm builds .4 or higher
Sent from my SM-G935V using Tapatalk
Sent from my SM-G935V using Tapatalk
Yeah. I use it when I'm building on my tube mech. I've watched some videos and I see some people using solder flux. Do I need that?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Will it give me the hard hit that I get from my AV stacked 18650 tube mod?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
If you were using a series mech at .15 your lucky to have a face to be honest. Your batts are probably damaged at this point as well.
YouTube analogboxmods
You can find his videos for building unregulated (parallel or series) and regulated(DNA) if you choose.
You can find his videos for building unregulated (parallel or series) and regulated(DNA) if you choose.
Parallel - good for complex multi-core fancy builds that are inherently very low resistance where a large amp pool is required.
Series - good for large higher resistance coils and super fast ramp up times.
Series is more efficient because you are not dealing with the issues associated with very high current levels.
Series - good for large higher resistance coils and super fast ramp up times.
Series is more efficient because you are not dealing with the issues associated with very high current levels.
I appreciate that info. I mainly use the "fancy" builds (aliens, staggered fused claptons). I plan on building one. Once I get that done and see how hard/easy it is I plan on building another in the other configuration.
Sent from my iPhone using Tapatalk
I may not be the sharpest room in the shed but I am sharp enough to know that's not kosher. I build about .3 on that. On my regulated devices I run it about .15-.2.
Sent from my iPhone using Tapatalk
That's good to know. You scared me a bit lol. .3 is pushing a bit too. It'd say .34 for series mechs. I build mine around. 5-.6 for a vape I like
And the .34 is with vtc5a batts
Sent from my SM-G935V using Tapatalk
So I looked at his YouTube channel and it seems all he builds are regulated box mods and mods with PWM. No just strictly unregulated/no electronics mods.
Sent from my iPhone using Tapatalk
Lol no worries.
What kind of builds are you doing to get the resistance?
Also, in my tube mod I'm running the LG HB6's.
Sent from my iPhone using Tapatalk
Hb6 are great. 30 amp batts can build low but battery life is short.
I do mostly fancy wire builds in mine.
That's for my tfv8 rba I put on my pwm mod
That's a .6 for my vcp (series mech)
I did a .4 for my series mech but it was hotter then I like personally
Sent from my SM-G935V using Tapatalk
I prefer parallel. that way I can switch between my parallel box and single tubes without rebuilding. (don't normally build very low)
that being said, sometimes I love to throw a huge build onto my series mod and make my wife mad. lol. dual 12 wrap 24 AWG kanthal with a 3 mm ID should come out to .5-.6 ohms.
if you're gonna do both, go for parallel first...more "versatility" imo.
but you gotta show us pictures when you're done!
that being said, sometimes I love to throw a huge build onto my series mod and make my wife mad. lol. dual 12 wrap 24 AWG kanthal with a 3 mm ID should come out to .5-.6 ohms.
if you're gonna do both, go for parallel first...more "versatility" imo.
but you gotta show us pictures when you're done!
He does have one video for each parallel,and series i am not sure if he took them down but I know he had one for each posted ??
Hb6 are great. 30 amp batts can build low but battery life is short.
I do mostly fancy wire builds in mine.
That's for my tfv8 rba I put on my pwm mod
That's a .6 for my vcp (series mech)
I did a .4 for my series mech but it was hotter then I like personally
Sent from my SM-G935V using Tapatalk
I like a hard hitting, warm to hot vape with dense clouds and good flavor. That's why I thought Series would be good for me. I did research on cells a while back and I had read numerous times that the hardest hitting cell what the HB6 so I got a few of them to run in my AV tube mech. In my RX300 wight now I have a dual alien wrapped 7 times over a 4mm coming in at .19 running it at 220W. I could go higher in wattage if I wanted.
What kind of tank you you have on there in the last pic? I'm liking the looks of that. Not much of a tank person since I like wide open air flow (running the Mason with airflow wide open). I like it airy. Had the TFV8 and waiting on the TFV12 to come in the mail and hope it's not too restricted. The TFV8 was too restrictive so I got rid of it to a friend who was just getting into vaping.
Thanks for the info Anthony! I know I do want to build a series and then a parallel mech so I can have one of each but I have a feeling there is going to be a few of these box mod builds in my future!
Sent from my iPhone using Tapatalk
- Status
