What are Lorann single flavor percentages?

Status
Not open for further replies.

kweni16

Full Member
Sep 6, 2012
22
12
Philippines
Hi everyone! I know this should be on the DIY sections but I'm not allowed to start a new thread there just yet. I just needed some help and info on the percentage of Lorann flavoring I should use on my mix.

I don't have the luxury to waste these Loran flavorings that just came to my door because they're really not available in my country. I'm pretty sure I saw a thread here as to how much percentage I should put ony my DIY but I can't find it anymore. if anyone could, please reply with the link on it.

Anyway, so here are the list of flavors that came in:
- blueberry
- butter
- cheesecake
- chocolate hazelnut
- lemonade
- mango
- marshmallow
- mint chocolate chip
- peppermint
- strawberry kiwi

The only flavor enhancer I have available is ethyl maltol. Please guys I need your suggestions TIA!:)
 

Scottibones

Senior Member
ECF Veteran
Verified Member
Jul 20, 2012
205
117
Fort Myers, Florida
The flavor percentages will vary based on your base liquid pg/vg ratio. pg carries the flavor much better than vg. I would suggest starting by making 5 ml batches that way any changes will be minimal hence little to no waste. Personally I diy 100% vg so my flavor ratios tend to be on the high side.
 

Razloz

Senior Member
ECF Veteran
Jul 8, 2012
147
30
Virginia Beach
Yea start low and work your way up, you can always add more flavoring, but you can't easily take it away. I use 50/50 vg/pg in my DIY and usually end up using about 10% flavoring with loranns. I would suggest starting at 2% or 5% though to see how you like it. Definitely make small batches as well, and without nicotine until you get the flavor right. Nicotine is the expensive part in DIY at least from my experience.
 

Vappa

Super Member
ECF Veteran
Aug 30, 2012
443
201
Netherlands
Anyway, so here are the list of flavors that came in:
- blueberry
- butter
- cheesecake
- chocolate hazelnut
- lemonade
- mango
- marshmallow
- mint chocolate chip
- peppermint
- strawberry kiwi

I'm actually testing the chocolate hazelnut these days. So far 10% in 70/30/11 PG/VG/mg tastes quite good. The chocolate is more present than the hazelnut and its taste is a little dry (probably from the chocolate). I will try this on 12% later on.
 

Vappa

Super Member
ECF Veteran
Aug 30, 2012
443
201
Netherlands
Hi Judy, in general the Lor Anns are not very strong. Well at least compared to the Flavour Art i'm also using.
Most of Lor Ann are in the range of 10 - 25%. The strongest flavor i tried so far is the Coffee @6%. It is a very dry coffee flavor without any sweet at all, but quite strong at that level. It needs something else added to it though.
 

TxTunesLady

Senior Member
ECF Veteran
Verified Member
I have all TPA flavors and have had horrible sucess with anything coming out, as well as the capella's BUT with LorAnn's I have gotten a good result, I am working on them now the only once I have, but the - chocolate hazelnut YUM at 17% but I am going to try it at 22%. My taste buds haven't fully come back so each week things are tasting really different. like what I once LOVED this week is just so so. The cheesecake blah! I like TPA better. Ill fill u in on the other flavors later.
I have the Caramel, Chocolate Hazelnut, Cinnamon Roll, Bav Cream, Keoke Coffee, and Peanut Butter
The LorAnn Caramel is light to no flavor for me at 20%
Bav. Cream to light at 15%
Keoke Coffee light but not bad at 12% but want to try stronger
PB and Cinnamon I havent tried yet and am doing those as I type this
 

Vappa

Super Member
ECF Veteran
Aug 30, 2012
443
201
Netherlands
I mix the Caramel at 9% now. It tastes good this way, but could be a little stronger like 12%.
The peanut butter is in my current test batch @20%. I've tested it at 15% and was nice but not strong enough. I didn't test the 20% batch yet.
Cinnamon Roll i used at 20% and was already quite strong. But i want to push it to the limit and try it in a batch @25%, just to see how this works out.
 
Status
Not open for further replies.

Users who are viewing this thread