What's the best Atty for 5v?

[dysfoundation]

Like said above, I have been using 510 and never strayed from them but I'm growing tired of how they are very finicky with certain flavors

Ex: cinnamon
So what's a good Atty that has over 3ohm? I hear 901s are native 3.3ohm but i have no experience with them
Sent from my T-Mobile myTouch 3G using Tapatalk

 

[wv2win]

I've used 510's, 901's and 801's and I only vape on 5 volt models. IMO, the 801 is the best. I actually use the BE112 version of the 801 and drip. They have about a 3.3 resistence. They give a great TH but with no burning and if you use a cart, they have the largest cart around. You can get them at Liberty Flights or BestEcig.

 

[basilray]

I find 510 SLB's to be the best at 5v. They typically rate in right around 3.0ohm for me.

In my opinion, if you get lower or higher than 3.0 ohm at 5v, you either burn out too much flavor, or don't get enough flavor.

 

[dysfoundation]

I find 510 SLB's to be the best at 5v. They typically rate in right around 3.0ohm for me.

In my opinion, if you get lower or higher than 3.0 ohm at 5v, you either burn out too much flavor, or don't get enough flavor.

i use a 3ohm 510 right now but i just dont have enough flavor from it, tons of th but not flavor

 

[basilray]

i use a 3ohm 510 right now but i just dont have enough flavor from it, tons of th but not flavor

One would assume you're dripping if you're at 5v, correct? If so, I would suggest a possible de-bridge/wicking and seeing if that helps.

 

[dysfoundation]

oh i drip and have all my attys set with no bridge and all that just looking for a varience in an attomizer but how it seems i might just stay with 510s

 

[basilray]

oh i drip and have all my attys set with no bridge and all that just looking for a varience in an attomizer but how it seems i might just stay with 510s

I haven't used them very much, but I got great flavor, good vapor, and just enough TH from a Cisco 801. Can't speak for 801's in general, but it's always worth a shot.

 

[dysfoundation]

Yea I filled up My shopping cart with a 510 and 901 so we'll see how things go thanks for the help guys

Sent from my T-Mobile myTouch 3G using Tapatalk

 

[wv2win]

I haven't used them very much, but I got great flavor, good vapor, and just enough TH from a Cisco 801. Can't speak for 801's in general, but it's always worth a shot.

Where do you get your Cisco 801's?

 

[benjayman2]

Where do you get your Cisco 801's?

801 Atomizer - Avid Vaper these are his standard ones which I think should be fine at 5v

 

[wv2win]

801 Atomizer - Avid Vaper these are his standard ones which I think should be fine at 5v

The resistence for these 801's show is 2.2 ohms. Regular 801's are about 3.3. That seems like LR to me.

And does anyone have a supplier for 302 atomizers?

 

[benjayman2]

The resistence for these 801's show is 2.2 ohms. Regular 801's are about 3.3. That seems like LR to me.

And does anyone have a supplier for 302 atomizers?

Sorry I didn't notice that. I've used IKV801 semis that are 2.5 ohms at 6v and have not had any problems.

 

[dspin]

I like Ikenvapes HV 901's for 6V - I also use his HV801's standard size (on sale now)but cut 1 1/4" off w/a pipecutter for a better vape. Little over 6v drops to about 5 1/2 v after few minutes of use.

Like said above, I have been using 510 and never strayed from them but I'm growing tired of how they are very finicky with certain flavors

Ex: cinnamon
So what's a good Atty that has over 3ohm? I hear 901s are native 3.3ohm but i have no experience with them
Sent from my T-Mobile myTouch 3G using Tapatalk