Why does my atty get so hot?

[Coffee Addict]

I use a lr306 and it gets so hot (only when activated) that it burns my lips to touch them to the drip tip. This also happens with the 510 atty.
I know there is enough juice in there, but as soon as I push the utton the attomizer gets too hot to even remove.

 

[Credo]

Do you happen to know the resistance? LR atties?
Some of the LR coustom 306 stuff can get awfully hot (up to 9 watts or more).

Maybe try some higher resistance ones if the one's you got are too hot for you.

Maybe look into some different drip tip designs/materials.

 

[Rhapsodies Fire]

Hi Coffee Addict Can i ask what your setup is? battery and atties...

 

[tybin]

metal drip tip?

 

[Coffee Addict]

cisco lr attys
AW imr (red) batteries
Delaron drip tips or nhalers twisted drip tips.

Have used the same set-up on othe mods and it worked ok.

 

[Rhapsodies Fire]

interesting. my 306s get warm on the tips, but nothing serious. My 510s are the same. If i touch them near the base...they are hot. But these are are too hot for your lips? That seems a bit alarming. Do you have a multimeter to check your batteries and atties to see where they're at? I suggest sending Rob a PM if this continues.

*edit...Credo could be right as well. Do you know what the resistance is on your atties?

 

[Coffee Addict]

Well I do not have a multimeter. And yws, I have burn marks on my lips from them.
I have tried different juices and everything else I know to do.
Maybe I can try wrapping something around the atty.

 

[tybin]

sounds like it's time for DR. ROBERT

 

[Mudflap]

Don't wrap your attys. Retire them for now and use something else. It's time to buy a multimeter.

Good news... they're fairly cheap.

 

[uba egar320]

My 801's used to get real hot if the connection had juice all over it. Doubt if it will solve your problem. But wiping down the contacts and threads is worth a try if they are wet. Good luck.

 

[Rhapsodies Fire]

Well I do not have a multimeter. And yws, I have burn marks on my lips from them.
I have tried different juices and everything else I know to do.
Maybe I can try wrapping something around the atty.

Hmmm...I would contact Rob and discuss sending the mod, the battery, and the atties in for him to take a look see. That just doesn't sound right at all. In the meantime, wrapping your atty will only trap more heat, so I strongly advise against that. If you don't have an atty that doesn't get hot on the mod, then I would stop using the mod for now and get a hold of Rob right away.

 

[redeyedancer]

You could very well have a atomizer with a lower ohm rating it happens every once in a while I run into atomizers that rage. Try another atomizer and battery for sure. Avid vaper atomizer 1.5 are hot little attys to hot for some of my mods imo .I am not sure what other mods you have but if your comparing it to a ego type ecig there is a big difference. If another atomizer battery doesn't help send it to me I will go through the mod Send the battery to .

 

[MacDiver]

I use minis with Cisco 1.5 - 510 attys and AW 14500 batts. Yeah they get really hot, so hot that if you give a nice long vape that it'll burn some if you do like I do and grasp the atty between the intersection of my thumb and first finger. But it's the heat I'm looking for and makes for a nice warm vape. When it gets cooler I switch to a fresh batt. My batts last about 2-3 hours before I switch them out.

Feel the burn or you ain't vaping right, hehe

Luv my minis!

 

[mlinky]

I use minis with Cisco 1.5 - 510 attys and AW 14500 batts. Yeah they get really hot, so hot that if you give a nice long vape that it'll burn some if you do like I do and grasp the atty between the intersection of my thumb and first finger. But it's the heat I'm looking for and makes for a nice warm vape. When it gets cooler I switch to a fresh batt. My batts last about 2-3 hours before I switch them out.

Feel the burn or you ain't vaping right, hehe

Luv my minis!

Me too. Love the heat and the hit

 

[mrengles]

You could very well have a atomizer with a lower ohm rating it happens every once in a while I run into atomizers that rage. Try another atomizer and battery for sure. Avid vaper atomizer 1.5 are hot little attys to hot for some of my mods imo .I am not sure what other mods you have but if your comparing it to a ego type ecig there is a big difference. If another atomizer battery doesn't help send it to me I will go through the mod Send the battery to .

I use the Cisco LR 2.0 attys and they work great. The 1.5ohms seemed to get too hot for my liking.

 

[Coffee Addict]

And where might I get Cisco LR 2.0. I like the heat too, but not when my lips are burnt.
Breaking in a new atty now, hope this helps.

 

[Credo]

And where might I get Cisco LR 2.0. I like the heat too, but not when my lips are burnt.
Breaking in a new atty now, hope this helps.

I'm pretty sure the ones identified as 'Coustom' at Nhaler are Ciscos. They usually have a good selection in stock.

Maybe the stuff that Inkenvape orders up? Not sure if they are Cisco, but they are supposted to be top notch stuff done the way he wants them.

 

[bornagainst]

I also invested in a few 306 CANNON tips. I suffered from dry/chapped lips badly, but once I got these (still on the same two from December), i never overheat my lips.

Good luck!

 

[mlinky]

And where might I get Cisco LR 2.0. I like the heat too, but not when my lips are burnt.
Breaking in a new atty now, hope this helps.

The only place you can get Cisco attys is at avidvaper.com The 2ohm 510's are a fabulous all-purpose atty LR510 Low Resistance Atomizer 2.0 ohm (Cisco Spec) - Avid Vaper and are not "hot"