WOW HOLY VAPOR DUAL 801 powered by dual 3.7v

[DaMulta]

Used two TW 801 Pen atomizers, and hooked them up to dual 3.7v batteries with a switch/led. Ran both atomizers into 1/2 tubing, and then into a water 3 way connector sticking the whistle tip in the end.

WOW WOW WOW

YouTube - WOW HOLY VAPOR DUAL 801 powered by dual 3.7v

Less vapor but LOVE has hit!

http://www.youtube.com/watch?v=ax2Bq0o1tDk

 

[Tyler2.0]

looks more like a 6ft .... rip!

 

[Doug Dino]

dude that's bad ........... we all have a lot of ideas, but you seem to DO a lot of yours, good work.

 

[Crash]

:O sweeeeeeeeeeeeeeeeeeeeeeeet lol

 

[Wormwood]

That is freeeaking amazing, its looks like your using scuba gear, except to do the opposite. hahaha omg. You have just turning into my role model modder. I wanna make one. Actually... I just want one!

 

[Wormwood]

i just gotta add. u can tell your fan is on, but still see clouds of thick vapor. Better watch out, your gonna have Leaford knocking at your doo with that kind of vapor production.

 

[DaMulta]

YouTube - Update on the HOLY VAPOR DUAL 801

I thought I would explain it a little more, and tried watermelon 36Mg in it.

I think dual 3.7 bats are too much for it, and plan to try it with 6v later on.

:O sweeeeeeeeeeeeeeeeeeeeeeeet lol

And you say 801 suck at vapor production ROFL

 

[Zofryer]

YouTube - Update on the HOLY VAPOR DUAL 801

I thought I would explain it a little more, and tried watermelon 36Mg in it.

I think dual 3.7 bats are too much for it, and plan to try it with 6v later on.




And you say 801 suck at vapor production ROFL

Wire the atty's in series instead of parallel. Wait until you see the four atomizer 510 mod I'm working on....

 

[DaMulta]

Brain fart....

Wire one to - and the other to + for it to be in series inside the box? Yet, that would kick the voltage in half. I think 6 volts over all would be much better, because I do enjoy the 801 at 6v.

4x501 LOL!!!!!

 

[Zofryer]

Brain fart....

Wire one to - and the other to + for it to be in series inside the box? Yet, that would kick the voltage in half. I think 6 volts over all would be much better, because I do enjoy the 801 at 6v.

4x501 LOL!!!!!

YUP! I've named the project "Raping Zamfir" because the prototype is starting to look like a pan flute.

Instead of pushing 7.4v out to each, run a pos to a negative from one atty to the other so they share the pain like one big atomizer.

 

[DaMulta]

Ok wired it up in series to share the load. Not as much vapor, but I know what the awful taste is. PRIMER!

Need to vape that off!!!

Still think that 6V is the way to go!

 

[Zofryer]

Ok wired it up in series to share the load. Not as much vapor, but I know what the awful taste is. PRIMER!

Need to vape that off!!!

Still think that 6V is the way to go!

Add another 3.7V battery then. : )

3.7 x 3 = 11.1

 

[Zofryer]

Here's an interesting thought I just had.....

3.7x4 = 14.8

14.8/3 = 4.93333....

So, four 3.7 volt batteries (maybe those little 10440's) wired in series, for 14.8 volts, connected to three 801's wired in series = three 801's in the 5 volt sweet spot. : )

 

[DaMulta]

Naw going to pick up two CR2 3v batteries, and wire it up parallel. Hope I can make it out to radio shack sometime tomorrow/

Also one of my atomizers stopped working for some reason....may of burned up lol one of them is firing up RED GLOWING stile!

Going to work on it in da morning.

It be SandMan time!

 

[mnealtx]

Nevermind, ya already got it...

 

[DaMulta]

Well I wired it back up into parallel, and the other atomizer started working again. Hmmm IDK

Well I think the sweet spot is 6v with the 801 personally not 5v. That is with me testing with 4 X AA 1.5 batteries.

 

[mnealtx]

I thought you had em both working?

You'd go from the switch to the center of atty 1 - from the outside of atty 1 to the center of atty 2 - from the outside of atty 2 back to the battery. That puts the atomizers in series with "proper" polarity - although with straight resistance it *shouldn't* matter.

Parallel, you'd "Y" from the switch to the center of both attys, then "Y" from the outside of both attys back to the battery.

 

[DaMulta]

I think I was not paying attention this morning lol...and last night....wired up just one atomizer.

yes in the videos both were working.


I bought another box, and some fittings today.

Going to make it nicer, and then maybe sell it to anyone that wants HOLY VAPOR!

I'm thinking I might run it off of 4 X AA batteries. That way if a user wants 6v he can use normal ones. I buy 20 packs for 5 dollars.....and they would last around 3 days on one atomizer. If you used normal rechargeable batteries(they do make 1.5v ones) it would run at 5v.

 

[DaMulta]

OMG

Installed 2 custom 801 connectors
Two bungee cable from a Y point into one
One, and off switch on the box


http://www.youtube.com/watch?v=ax2Bq0o1tDk

 

[Satyr]

That's nuts! I wonder what the FDA would think of that? lol