Hello folks and welcome back for today's review of the MVP Pod System from Innokin. The MVP name from Innokin represents toughness and quality in the past devices that were in the MVP lineup but Innokin decided to add a pod styled device to the MVP lineup which is a big departure from past MVP devices. Does the new MVP Pod System deserve to be included in the MVP line, that's what we will find out.


COLOR CHOICES

• Pink Fade
• Liquid Amber
• Stealth Black
• Ocean Waves
• Space Grey
• Blue Fade

INCLUDED IN THE BOX

FEATURES

• Size: 107x22x13mm
• Output: 2 power levels – 11W or 12.5W
• Battery: 500mAh (internal)
• Display: LED indicator
• Resistance limits: 0.4-3.5ohm
• E-liquid capacity: 2.7ml (standard) / 2ml (TPD)
• USB Type C Charging – 0.65A charge rate
• Pods: Refillable, fixed coil
• Coils: 0.65ohm
• Auto draw or button activation
• Side refill port

PARAMETERS


* Product name: Innokin MVP Pod Kit
* Size: 107.88 × 22.66 13.38 mm
* Battery capacity: Internal 500 mAh
* Pod capacity: 2 ml
* Resistance range: 0.4 ohm — 3.5 ohm
* Charging port: USB Type-C
* Charging current: 650 mA / DC 5.0V
* Coil material: KAL
* Cut off time: 10 seconds
* Max. Output currency: 7.0A


SIMPLE AND EASY TO USE





MVP QUALITY





GREAT COLOR CHOICES





LIGHTWEIGHT AND THIN





TYPE-C CHARGE PORT





DUAL ACTIVATION - BUTTON PRESS OR AUTO-DRAW





2.7ML CLEAR POD WITH SIDE FILL





2 POWER OUTPUTS - 11W OR 12.5W





OPTIMIZED AIRFLOW





MY IMPRESSIONS


As you saw earlier Innokin sent me 2 devices for testing, the Stealth Black and the Liquid Amber colors, Black is just that Black, but this Black is done in a nice matt finish with the fire button having a bit of a sheen to it that looks nice, the sides and bottom are done in a nice dark grey tone that pulls the 2 colors together nicely. Looking at the device it looks like the run of the mill pod system until you pull the pod out, remember this is a 2.7ml pod and it fits deeply into the device. Strong magnet are used to secure the pod to the device.




The Liquid Amber color is a multi-colored device that reminds me of the beach on a tropical island, I normally don't like patterns like this but Innokin did a nice job on it, I find myself grabbing for it more than the Black colored one which surprises me. On the sides and bottom as well as the black outline fire button is silver colored. Branding is on both side of the devices with MVP on one side and Innokin on the other.







One of the best features of the MVP Pod System is the huge 2.7ml side filled pod that fits inside the MVP device, it's deeply recessed cavity allows the pod itself to look like a normal 2ml pod, but there's a large addition of juice capacity deeper inside. The juice fill port hole is large with a rubber plug that is easily rotated out of the way when filling, and being clear you are able to view juice levels very easily.







When you receive your MVP Pod System you will have to remove a protective sticker covering the pod contacts before using, notice how deep the pod sits inside the device. One thing I want to note is that I have never been able to vape through a entire pod of juice before the battery became depleted, I averaged about 6.5 hours of vape time on a single charge and I think that shows the device is a juice sipper and not a guzzler.





Having a 500mAh internal battery means your not going to get a full day on a single charge, because the MVP is a simple device with no display screen or puff counter there's no way to tell how many vapes you will get , my average vape time was 6.5 hours before needing to be recharged, it takes about 1 hour to fully charged using the TYPE-C charge port located on the side of the device. Battery mAh is printed on the bottom of the pod device.







Airflow is feed to the pod through 2 tiny holes located on each side of the device, with the MVP Pod being a dual activate device you have the choice of button fire or auto-draw and I'm pleased to tell you that the auto-draw works great. I would say the draw on the device is a semi loose one, if you want a tighter draw you can use the old trick of blocking 1 of the air flow holes with a small piece of scotch tape although not much of a difference is felt.





The MVP Pod offers 2 power settings, 11w and 12.5 w. There is a difference between the 2 settings but it's very small, I like a warmish vape so most of the testing was done on the higher 12.5 w setting. Turning the device on/off is done by pressing the fire button 3 times quickly which will light the outside of the fire button green 11w, to change to the red color 12.5w simply press the fire button 2 times quickly.





The MVP Pod's battery meter is done in 2 colors with no mid range color that seems weird to me, fully charged the battery color is green and at 90% or less the battery meter color is red until at 10-50% then the red light stays lit for 2 seconds after being vaped, when the battery is under 10% the red light flashes twice, this can definitely be improved upon. Vaping while charging is possible with the MVP Pod.

Both activation modes work fine with the button being very responsive, I like how Innokin made the fire button slightly recessed into the device, it makes it easy to find by just feeling for it with no need to visually look for it.

The auto-draw on some devices are mediocre at best but the MVP's auto-draw works great, not once in the 2 weeks of testing has it failed to fire, great job Innokin.

Flavor from the pods is very good with no break in time needed. One thing to mention, when vaping the device in either auto-draw or manual button press mode a light hum or buzz can be heard coming from both devices.


PROS

* Thin

* Lightweight

* Very Good Flavor

* Clear 2.7ml Pod

* Auto-Draw Works Great

* Very Good Battery Life For 500mAh

* No Leaking

* Vape While Charging

* Attractive Color Choices

* Plenty Of Vapor

* Smooth Airflow

* Large Fill Port

* Mess Free Filling

* Side Fill





CONS

* Weird Battery Meter

* Hum Or Buzz When Vaping

* No Airflow Selection

* Can't Disable The Fire Button For Auto-Draw Only

WISH LIST

* Larger Battery

* Airflow Selector

* Replaceable Coils Instead Of Pods

* Ability To Disable The Fire Button


FINAL IMPRESSIONS


In the time of testing both devices never once did either of them fail to fire using either activation mode, I'm a button guy but I found myself using the auto-draw more because it works so well.

I think the Pods give very good flavor without needing a break in period. Being as thin and light weight as the MVP is it sometimes can get lost in a deep coat pocket with winter upon us now.

I love the finish of the devices as well as the color choices offered. I'm so glad the Innokin went with a clear Pod instead of tinting it so 1/3 of your juice can be seen without needing to pull the pod out for viewing. With This pod being 2.7ml and the battery being 500mAh I have not been able to vape a pod dry on a single charge and that shows that the pod is not very thirsty but more of a sipper saving on juice consumption.

If a MVP 2 Pod System is ever released and the cons and wishes in my list were addressed we might have a perfect Pod System finally.

When both of these arrived I took them to work as I do with all review products and on the 2nd day of testing my personal Pod System for work when indoors died so all I was left with was my Mod and RTA for outside and the 2 MVP Pod Systems. Over the next couple of weeks I found myself picking up the MVP more than my usual setup, the MVP is now my work Pod System and I won't be buying another of the one that died.

I would like to thank Anna and Innokin for providing both MVP Pod Systems for the purpose of this review, I would also like to thank my loyal viewers of my reviews and hope that all your questions were answered and addressed in my review.

THANK YOU
BIGBOB2322

Well I hope I can get the sensis to stop burning coils in Coil+ mode

SMOK Pozz Pro Pod System 1100mAh 25W vape Kit,SMOKTech SMOK Pozz Pro Pod System Vape Kit features its artistic and classic flat profile and is engineered for functionality and performance. Pozz Pro leads to an extraordinary lightweight, delivering an exquisite design for both air-activated and button-triggered ways to vape, which is convenient to switch freely and carry outside. What makes it a breeze and less complicated is its slider holds 4 levels of the airflow, depending on your demand, it is optimized for the volume of the airflow, resulting in taste restoration. Aside from that, Smok 1000mAh pozz pod 25W kit is reminiscent of the vaping paradise when inhale through an ergonomically curved mouthpiece. It earned its stardom and the success for leakage-proof technology by the three silicone rings.
SMOK Pozz Pro kit built-in 1100mAh integrated battery, promises to create a timeless piece that you can count on for some time to come, and utilizes a charging port to refresh in a full charge in less than 90 min. It adopts an adjustable voltage-based output that ranges from 5W to 25W, where determines the battery and flavor performance. On the side of the device fulfill a 0.69 Inch OLED display and UP / DOWN button to work hand in hand under your control. What's more, SMOK Pozz Pro Pod kit offers you a full protection suite for you vape security. Remove the classic color matching that follows already, Pozz Pro enhanced outer-body features and set itself apart from the rest of those in its class by its innovative pattern resembling an arrangement of pins.
More info SMOK Pozz Pro Pod kit
Battery Capacity: 1100mAh
Power Range: 5W~25W
Standby Current: <50uA
Input Voltage: 3.3~42V
Output Voltage: 1.5~4.0V
Resistance Range: 0.6ohm~2.5ohm
Charging Voltage: 5V +/- 0.2V
Charging Current: Max 0.98A
Over-charging Voltage: 4.3V +/- 0.05V
Over-charging Current: 1.75A +/- 0.6A
Over-discharging Voltage: 2.4V +/- 0.05V
Air-activated And Button-triggered Way
4 Levels of The Airflow
Three Silicone Rings
Compatible with LP1 Coils
1100mAh Integrated Battery
Less Than 90min Charging
0.69 Inch OLED Display
Up To 25W Output

Voopoo DRAG S PNP-X Kit is a compact and ergonomic pod mod system kit that consists of a 5ml pod cartridge and a 2500mAh built-in battery. With PnP-VM1 0.3ohm coil and PnP-VM5 0.2ohm coil, it is also compatible with the other PnP coils, which can bring you DL and MTL vaping experience. And regarding to the mod, it features adjustable power in the range of 5 to 60 wattages. Monitored by GENE.TT chip, it can ignite within 0.001s, and also provides intelligent functions such as PUFF recording, SCORE ranking, SMART switching start mode, and so on. Besides, there are 7 safety protections to ensure your safety, like Overtime Protection, Short-circuit Protection, Overcharge Protection, Max Power Protection, Output Over-current Protection, Over-Discharge Protection, and Over-temperature Protection.



Features:
1. 5 New Color of Knight
2. The New PnP-X Pod
3. Innovative Infinite Airflow System
4. 0.96 inch TFT Color Screen Display
5. New Generation GENE.TT Chip
6. Intelligent Wattage-matching
...

Click here for more:

Voopoo DRAG S PNP-X Kit: Voopoo DRAG S PNP-X 60W Kit

Prizes:
2*Smoant Charon Baby Plus Kit
We'll have 2 Winners
Each winner will get 1pc of the prize.
All the entries are optional.

Sourcemore x Smoant Charon Baby Plus Kit Giveaway, 2 winners, ends on Dec. 9th, 2021

Enter here

Wotofo 24mm Gear V2 RTA Rebuildable Tank Vape Atomizerhas been engineered to make a whole with its top cap for expanding the depth of flavor path and vape experience.
Wotofo Gear V2 single coil RTA creates its own performance to enlarge the working space, offers the best opportunity for every drop of your e-juice, the compressed chamber can produce massive flavor.
The advantage it has is its flexed side airflow control ability, which can calculate your air consumption and decrease e-liquid condensates. Come with its 3.5ml vape juice capacity and top filling system, Wotofo 24mm Gear V2 RTA works best between 40W and 55W output. Wotofo gear v2 rta measures 24mm diameter and acts the next level in your vaping journey. Not only is it's functional, but look at this fine glass artwork, made by German PEEK for its insulator, Stainless Steel, and PCTG for its appeal, simple but stylish.

More info Wotofo 24mm Gear V2 RTA
510 threading connection
E-liquid Capacity: 3.5ml
Filling Method: Top Filling
Main Materials: SS + PCTG
Coil Type: Single Wire Coil
Airflow Type: Fixed Side Airflow
Insulator Material: German PEEK
Coil Included: Framed Staple Clapton
Material: Ni80
Resistance: 0.33ohm
Inner Core: 28G + 38G x 9 + 28G
Outer Wire: 36G
Internal Diameter: 3mm
Power Range: 5~60W (Best At: 40~55W)
Flexed Side Airflow Ability
Calculate Your Air Consumption
Decrease E-liquid Condensates
24mm Diameter

These tests below only note my personal ESTIMATED ratings for the batteries I tested at the time I tested them. Any battery that is not a genuine Samsung, Sony, Murata, LG, Panasonic, Molicel, or Sanyo can change at any time! This is one of the hazards of using “rewrapped” or batteries from other manufacturers so carefully research any battery you are considering using before purchasing.

Misusing or mishandling lithium-ion batteries can pose a SERIOUS RISK of property damage, personal injury, or even death. They are not supposed to be used outside of a fully protected battery pack and you use them at your own risk. Never exceed the battery’s true continuous current rating and keep the plastic wrap and top insulating ring in perfect condition.

Testing batteries at their limits is dangerous and should never be attempted by anyone who has not thoroughly studied the dangers involved, understands the risks, has the proper equipment, and takes all appropriate safety precautions.

If the battery has only one current rating number, or if it only says "max", then I have to assume the battery is rated at that current level for any type of discharge, including continuous.




Test Results
Lishen is one of the large, established cell manufacturers in China (天津力神电池股份有限公司). This cell is a decent performer, about the same as the Samsung 50E but not quite as good as the Molicel M50A and Samsung 50E3. Its 12A rating seems reasonable but must be reduced to 6A if the cells get above 45°C, what many would call “warm”, up to a max of 60°C. This type of derating should be done for any cell in my opinion but Lishen actually specifies the derating in the datasheet, which is great to see.

Note that this cell has a low voltage cutoff of 2.75V versus the more common 2.50V cutoff used by most other cells.

This is a larger cell, the datasheet lists the dimensions as 21.7mm±0.2mm diameter by 70.9mm±0.2mm long.

The two cells I tested delivered 4022mAh and 4048mAh. This is decent consistency and is typical for cells from one of the larger China cell manufacturers.

This cell has a high cycle life rating “1000th cycle ≥80% of 1st Capacity (25℃±2℃，4.2V-3.0V). If discharged at high rate or high temperature frequently, cell cycle life will be shorten.” But note that the cells were discharged down to 3.0V. Most cycle life ratings are based on cycling the cell down to its low voltage cutoff point, 2.75V in this case. I do not know how much only going down to 3.0V extends cell life but we cannot directly compare this cell’s cycle life spec to a cell that was discharged all the way down each cycle.

Two cells were purchased for testing by me.


Continuous Current Discharge Graphs



Ratings and Performance Specs Graphic


I want to work for the community full time! If you feel what I do is worth a couple dollars a month and you would like early access to battery availability, battery and charger testing and news, and a say in what I test, then please consider becoming a patron and supporting my testing efforts: Battery Mooch is creating battery and device tests | Patreon.

To see how other cells have tested check out this link: List of Battery Tests | E-Cigarette Forum

Today,I want to introduce you the CBDfx CBD Vape in stock. CBDfx makes some top-notch CBD-infused vape oils, but what if you don’t already own a vape? This vape starter kit is their solution — offering customers a package deal with a rechargeable, refillable vaporizer and your choice of CBD E-liquid. This gives new users a good opportunity to step into the world of refillable vapes, and away from the wasteful practice of using pre-filled vape pens.

As a refillable vape, the upfront cost is higher, but in the long-run, this product will save you a lot of money because all you need to do is top up with new E-liquids when you run out.

This is a high-value starter kit for anybody looking to upgrade their vaping experience. If you wanna more details about it,please go to online vape shop to visit more clearance vape.

You may also like:

hyde edge rave recharge 4000 puffs
voopoo drag s pro pod mod kit

Hi, Freemaxers! Do you know where to buy Freemax Vape Products? If you’d like to buy Freemax vape products but can’t purchase them in your local vape shops, you can buy Freemax products in Freemax official vape shops. Freemax vape shop opens again now.

Please click here to enter Freemax vape store: https://www.freemaxvape.com/store

At the same time, welcome to join Freemax’s activity of “Dreaming Back to Sub Ohm Era”, you can get the coupons for up to 50% Price Off. Now seize the best chance to buy your favorite vape devices in the Freemax vape store. The valid time of this activity is from 12.1 to 12.7.

As the freezing times approached us, brighten your day up with a shiny and colorful XROS II.

I reuse these bottles over and over with DIY juice and over time they get "creases" in them resulting in spots where it is easier to squeeze the bottle. I imagine that this results in weak spots where the bottle will eventually break. Has this happened to anyone? Is it a sudden and catastrophic failure resulting in a big mess, or does it start as a little leak giving you enough time to transfer to another bottle?

Head to eJuice.deals, enter code Dec20 for a 20% off coupon valid on everything on the site!

Save 20% on hardware, disposables, ejuice bundles, our popular mystery ejuice bag, and all our salts nics!

Not find exactly what you like? How about 50% off this collection only? Use this code 50off for the massive eJuice discount!

Been vaping a while now and it’s mostly disposables.

I got some spit back and my lips became burnt. Not healing because I’ve been picking on find scab.

Question: is this normal? Can the hot liquid actually burn lips?

Dear Customers,

Friends, are you still interested in vape shopping on Black Friday Vape Deals 2021? Or missed the event time? Don't worry, the return event is coming!

From 01.12 to 05.12 US time, we vapesourcing also have a 12% off Black Friday return event. You only need to use the discount code: RE12 to buy it at a discount.

In addition, we also have flash sales for 6 products(discount codes cannot be used for these 6 products). What are you waiting for? Don't miss it this time. You can click on the event page for more details: Vape Shop Online E-Cigarette & E-liquid Best For Sale

Related products we guess you like:
Vandy Vape Pulse AIO Kit 80W
Eleaf iStick Pico Le Kit With GX Tank

Freemax has an activity of Dreaming Back to Sub Ohm Era, and the time of this activity starts from 1st, Dec to 30th, Dec. And this activity time is divided into three stages.

Now let’s join in the first stage, which is from 1st, Dec to 7th, Dec. In this stage, you will have a chance to win Freemax Maxus 200W Golden Limited Edition. Once you click the button on the activity page, you can get some coupons for up to 50% Price off. This is Freemax's Official vape shop: https://www.freemaxvape.com/store/ Don’t forget to use coupons.

Please click here to enter this activity: https://www.freemaxvape.com/dreaming-back-to-sub-ohm-era

Your best double battery partner choice, left or right？

The Yocan B-Smart Slim Twist Battery for sale, which is a compact and discreet battery, sleek, small and easy to use, the Yocan 510 Battery compatible with most of atomizers and the resistance should over 1.0ohm, you can use the herbal, concentrate and oil atomizers on it.

Parameters
Size: 86mm(Height) x 11mm(Diameter)
Battery Capacity: 320mAh
Voltage Settings: 2V-4V(0.1V Increments)
Thread: 510
Preheat Time: 10s
Colors: Black / Silver / Blue / Red / Gold

At the bottom of the B-Smart with the voltage adjustment dial, you can adjust the working voltage from DC2.0V to DC4.0V by twisting the dial to your desired voltage simply, the Yocan Mod Battery equipped with a 10 second preheat function which is best for preparing your materials before vaping.Rapidly click the power button two times to start preheat mode, it will last for 10 seconds, simply press the power button 1 time to end preheat, the LED indicator light will show you the working status.

Please go to vape stores to buy the cheap vape mod on cyber monday vape 2021 return.

You may also like:

hyde edge rave recharge 4000 puffs
caliburn price

I always ordered 18 mg and a 50/50 mix. Is this now outlawed???

I'm selling a like new condition Lost Vape Paranormal DNA 250C. I'm asking $105 shipped within the US ff with PayPal or buyer covers pp fees. I don't have the box but I do have the adapter for using it as a power bank. I may also have the booklet but haven't found it yet.

Proverbs 4:18
But the path of the just is as the shining light, that shineth more and more unto the perfect day.


Sent from my iPhone using Tapatalk

The SXK PROtocol Atom Bridge RBA Clone is made from 316 stainless teel and PEEK and is suitable for Billet / BB Mod Kit / Ambition Mods Sun Box 2.0 and other Boro Devices.

The SXK Atom Bridge RBA Clone is with C style post and comes with 3.5mm / 4.0mm Airflow Pins.

The Atom Bridge RBA can be break into 4 parts and the middle tank tube can be replaced with PEI / PC tank which can be buy separetly. Using the SXK PROtocol Atom Bridge RBA Replacement Middle Tank Tube PCTG / Ultem, the atom bridge rba looks beautiful in your boro tank and you can see the coil inside.



SXK offers Atom Bridge RBA DL Airflow Pin and Atom Bridge RBA MTL Airflow Pin to meet the DL / MTL vaping demand. the air pins is not come with the atom bridge rba but can be get from 3fvape.com separetly.

Features:
SS316F and PEEK Insulators.
Hand polish finish.
C style posts.
Package includes 3.5 and 4.0 airflow pins.
Spare O-rings and screws.
Suitable for Billet / BB Mod Kit / Ambition Mods Sun Box 2.0 and other Boro Devices.

Click to check more details for the Protocol Atom Bridge Clone by SXK

These tests below only note my personal ESTIMATED ratings for the batteries I tested at the time I tested them. Any battery that is not a genuine Samsung, Sony, Murata, LG, Panasonic, Molicel, or Sanyo can change at any time! This is one of the hazards of using “rewrapped” or batteries from other manufacturers so carefully research any battery you are considering using before purchasing.

Misusing or mishandling lithium-ion batteries can pose a SERIOUS RISK of property damage, personal injury, or even death. They are not supposed to be used outside of a fully protected battery pack and you use them at your own risk. Never exceed the battery’s true continuous current rating and keep the plastic wrap and top insulating ring in perfect condition.

Testing batteries at their limits is dangerous and should never be attempted by anyone who has not thoroughly studied the dangers involved, understands the risks, has the proper equipment, and takes all appropriate safety precautions.

If the battery has only one current rating number, or if it only says "max", then I have to assume the battery is rated at that current level for any type of discharge, including continuous.




Test Results
This cell looks the same as the Molicel P42A but performs just a little bit worse than the 2021-dated P42A’s I have tested. I don’t think you will notice the difference in actual use though.

In my opinion this cell’s 20A rating is conservative. That will help to reduce risk, increase performance, and extend overall cell life. It is nice to see a cell wrapping company do this as so many of them exaggerate the current ratings.

Unfortunately the 4200mAh capacity rating of these cells is slightly exaggerated. The two cells I tested delivered 4077mAh and 4098mAh. Since I cannot have the lowest capacity cells in the batch I am rating them at 4000mAh. This is the same as the P42A’s minimum rating.

These cells should be available in Europe so if you are unable to find Molicel P42A’s there you could try these.

Two cells were donated for testing. Thank you!


Continuous Current Discharge Graphs



Ratings and Performance Specs Graphic


I want to work for the community full time! If you feel what I do is worth a couple dollars a month and you would like early access to battery availability, battery and charger testing and news, and a say in what I test, then please consider becoming a patron and supporting my testing efforts: Battery Mooch is creating battery and device tests | Patreon.

To see how other cells have tested check out this link: List of Battery Tests | E-Cigarette Forum

Marvos S 80W Kit has five colors for options: Silver-Grey, Gunmetal-Red, Gunmetal-Yellow, Black-Black, and Black-Blue, coming with one Marvos DTL Pod, a 510 adaptor, and Marvos S 80W Mod. With a 510 connector, you can also match the other kinds of vape tanks with your Marvos S 80W Mod.

As for you, which color do you like best?

Innokin is presenting its "Why Smoke?" campaign in London running from Nov 29th till Dec 12th, featuring branded buses, vans, and projection displays on buildings throughout the city.

The "Why Smoke?" message, along with promotional displays for the brand new MVP Pod, will appear on 500 buses throughout the British capital for two weeks. Innokin is determined to help millions of smokers, not just in the UK but worldwide. Making cigarettes a thing of the past is an important message to spread across worldwide. "Why Smoke?" is just the beginning of Innokins mission to create a smoke-free future.

Share your thoughts with us about this campaign! We will randomly select winners and each will win a UK limited edition MVP Pod & other amazing Prizes!

More Entries, More Winners!



How to enter:

1. Visit Why Smoke? Vaping Made Easy | INNOKIN® for more information about this campaign.
   
2. Share your thoughts on the "Why Smoke" campaign below.
3. You must be the legal age in your country to enter. Winners will be required to provide ID and address for age and location verification.

Good Luck!

Best Regards,
Innokin Team