Search results

No matter what they called it, Bakero, Fettuccine, Linguine, Ribbon Kanthal, it is still a 'Flat' heating wire. Flat wire = more surface, more heat, less resistance. In order to achieve the huge vapor craze, Air-hole on your dripper/atomizer/tanks. Make it bigger. Get some 'Flat'...

Haven't tried since all my normal Kanthal wires are left sulking on the shelves lol, haven't look back since Ribbon-Kanthals. The normal method would be the 'twisted' but you could try it and debunk the myth it had to be twisted. :)

Ah here's the link: http://www.e-cigarette-forum.com/forum/modding-forum/330407-500-ss-mesh.html Look for 'BJ43''s comment.

Yes, I read a forumer did some test with all the meshes and builds(he uses kerosene with some cotton on top of each build and watch the fire burn intensity, flickering, etc lol), found higher density (roll solid) and finer mesh like the #500 wicks the fastest and never runs dry, best capillary...

It's just gunk, i.e. sugar burnt on the coil which you can wipe with piece of tissue. Some ejuice tends to have more, especially Boba's Bounty and that's why it's so tasty. Here's a suggestion: try oxidizing only the top mesh where your coils will be and leave the rest of the other half...

Been following your article on for months and it's proven true especially using the Ribbon Kanthals, the wide surface of the ribbon kanthal gave more intense heat than a normal Kanthal A-1 of the same resistance/wattage/voltage. I think Ribbon Kanthal needs a better/new measurement system to...

rotfl! anyway, the correct resistance for 0.4mm x 0.1mm is around 0.8 ohms/inch, sitting somewhere between a Kanthal A-1 30 awg and 31 awg. Sorry I forgot to put the ohm/inch of the ribbon kanthal I was using. Just remember I'm showing a 'folded' ribbon kanthal and not a normal ribbon kanthal...

Love my IGO-L, easy to set-up and looks great on any PV> and oh, we dry-burn our wicks here for a quick clean so we can drip other juices lol the con is, after dry-burning too many times, the silica wicks will get hard and doesn't wick as good. it's ok though since it's a dripper. :)

#500 solid/full ss mesh with a 70mm width on my AGA-T+. not single drop left in the tank. It's also the only wick that can keep up with my ribbon kanthal setup. straw wicks just can't keep up. I've only oxidize the top part where the coils are, helps with keeping the ejuices clear although if...

Ribbon kanthal wraps like a belt. I'm hooked on this.

roll a solid SS mesh with 70mm (width) and constantly try it on the wick-hole. as for the top wire hs, take out the middle knurled nut and add 2 washers:

My first post on my new find though I'm sure I'm not the first with this idea. Concept is simple, fold a ribbon kanthal of same length to get the 'twisted kanthal effect', shelving the resistance into half. BTW I only have ribbon kanthal 0.4mm x 0.1mm but with folding, I get a...

Thanks for the intro to ribbon kanthal Odysseus, Just found out a week ago we could actually do the 'twisted kanthal' (shelving the resistance by half) and 2x the surface coverge of the mesh by 'Folding'' the 0.4mm into 2 equal length before tightening the folded corner the negative post and...

Folded Ribbon Kanthal from a 0.4mm x 0.1mm to get the twisted Kanthal effect (shelving the resistance by half). So much easier to handle once it's folded and you will get 2x the heat too. Hugs the mesh like snake/belt.

Register and log in to Vaporbreak.com and grab your VAMO V2 there, USD 26.99 bro...

You'll need a license to ship/import any nicotine-based liquid and pure nicotine is darn right lethal. flavorless and sips through skin it could kill anything in pure form. you might find 'diluted nicotine' at 38-40mg around if you look hard enough but nobody's gonne sell you 'pure' nic in...

I got my black chrome Vamo v2 for USD 26.99 (body only) + USD 4 for China/HK-post shipping. Just takes slower to arrive 14-15 days. Vaporbreak.com (you have to register and log in to see that USD 26.99 or you will see USD 39) and zainy.net (USD 39). Think I might get another as a back-up lol

we are already doing it, well, until LowYat forums admin deleted out thread. sigh here's another MY forum cater for Malaysian Vapers : Mari Vape! • Index page

you can open a metal fabrication shop while you're at it bro! lol

Co-op buy is made famous here at ECF when Modders post a msg to check how many would want to pre-order their mods so the modder could estimate how many he should make and for serialization on the product.