Search results

Is it a clone or authentic? Not sure about the authentic, but some of the clones had an issue where some of the ematel material is in the threads of one of the posts on the deck. (Not the centre pin, either the left or right post unscrews from the deck below where you mount your various decks...

I remember hearing they were making a squonker deck. Maybe that's what it is? Sent from my iPhone using Tapatalk

according to one of the reviews on the page, it seems the high voltage is a clone of the vision MK Vision MK Tank Launch

Temperature control is pretty hit or miss. When it does work properly, and or you figure out the workarounds to have it working more often, it's really sweet. However, temperature control aside, I'm still happy with the upgrade as it brings other benefits. For example the 10 extra watts, the...

Since my DNA 40 upgrade. All batteries that didn't work before, work now. I guess the connector pins must have been pushed in a little or something before. Sent from my iPhone using Tapatalk

I have this mod. It's nowhere close to a DNA 40. Temperature control doesn't really work. I like my istick 50 watt more than this one. It doesn't do temperature control either, but it doesn't claim to and it does wattage pretty accurately. Sent from my iPhone using Tapatalk

nevermind, got it to work on my computer, my phone was just being a piece of icrap

I can't load that video for some reason. Anyone have another link? Sent from my iPhone using Tapatalk

Upgrade successful. Thanks for the input turbocad6 and mark78. And special thanks to @engineer for doing the work Sent from my iPhone using Tapatalk

Sorry. Never mind. I found it here: https://provape.zendesk.com/entries/58233684-ProVari-3-Software-Versions Any more detail though as to what was changed cosmetically? Sent from my iPhone using Tapatalk

What's new in software version 3.6? I tried searching, but couldn't find the info. Sent from my iPhone using Tapatalk

Here's a pic of Sammy, 3100 flat efest and 3100 nipple efest. Sent from my iPhone using Tapatalk

A lot of batteries that used to work in my WAE2 stopped working after a while as their top got a little compressed. So they end up needing magnets too. (Eg VTC5, purple efest 2500mah, LG). The efest purple 3100mah flat top batteries are longer than most (nipple top are too long). I use those...

Samsungs didn't work with mine either. However. I use tiny little magnets that make the batteries look like nipple tips for the shorter batteries, and they work fine. Sent from my iPhone using Tapatalk

Hey turbocad6 or mark78. A friend of mine is upgrading my WAE2 with the DNA 40. Got it in and having some problems. 1 the battery compartment is a little longer now and most batteries don't make contact without a magnet to extend and 2 the top cap by the 510 connection leaves a little gap now...

Question for Mark. I know swapping to the DNA 40 chip is physically possible but challenging (plastic rails need to be machined out). Asides from physical, is there any technical reason it shouldn't be done? For example will the board not have enough breathing room and overheat since it will...

I can build coils no problem. I just really like the Atlantis and Subtank coils. I tried the rba part of the Subtank and didn't like it as much. Less liquid capacity and tighter draw. Sent from my iPhone using Tapatalk

True if there was .7 ohm could for the Subtank, is use my Provari more (I'm ok with 20 watts). But the 1.2 ohm coils aren't cutting it Sent from my iPhone using Tapatalk

Any chance provape will consider an update to allow 0.5 ohms? Since all I use now is the Subtank and Atlantis, my p3 is getting little use and I'm considering selling it. Only reason I would hold onto it, is if there is a possibility of such an update. Sent from my iPhone using Tapatalk

I've been wanting to upgrade my wizard to dna40 also. You mind sharing some tips / instructions? Maybe even a tutorial? Sent from my iPhone using Tapatalk